Guest greeneggs Posted April 19, 2003 Report Share Posted April 19, 2003 When MDK hangs during boot...when your sitting there watching the lines of text scrolling down the screen and suddenly it gets "stuck" on "loading latin.inc" or some other line...after you've waited a very reasonable 5...10...15 minutes...what do you do to avoid having to run an integrity check each time and compounding your errors each time you do this? A) Reset button? B) On/off button? C) Ctrl+SysReq? D) Grab a bag of cheetos and just wait? - Peace Quote Link to comment Share on other sites More sharing options...
Ixthusdan Posted April 19, 2003 Report Share Posted April 19, 2003 I would be thinking about replacing..........the power supply! :mystismiles: Quote Link to comment Share on other sites More sharing options...
Guest greeneggs Posted April 19, 2003 Report Share Posted April 19, 2003 I would be thinking about replacing..........the power supply! :mystismiles: Wait...twist my arm...OUCH!...Ok, ok, tommorow this puppy is getting a new power supply! :P Quote Link to comment Share on other sites More sharing options...
qnr Posted April 19, 2003 Report Share Posted April 19, 2003 I would tend to agree with Ixthusdan. However, I haven't been following the other thread since it went into multiple pages, so I don't know if you have checked your RAM. A bad stick of RAM will cause intermittant problems too. In answer to the question about what to do. Always choose C. Alt+SysRq. ---- and R,S,E,I,U,B (just write down RSEIUB somewhere) <Alt><SysRq>-r -- raw (raw keyboard mode, gets keys directly) <Alt><SysRq>-s -- sync (write unsaved files) <Alt><SysRq>-e -- term (gently terminate programs) <Alt><SysRq>-i -- kill (rudely kill programs that didn't finish up with term) <Alt><SysRq>-u -- umount (unmount the file systems, remount read-only) <Alt><SysRq>-b -- reboot Always follow the sequence in the order given. Quote Link to comment Share on other sites More sharing options...
Guest greeneggs Posted April 19, 2003 Report Share Posted April 19, 2003 I would tend to agree with Ixthusdan. However, I haven't been following the other thread since it went into multiple pages, so I don't know if you have checked your RAM. A bad stick of RAM will cause intermittant problems too. In answer to the question about what to do. Always choose C. Alt+SysRq. ---- and R,S,E,I,U,B (just write down RSEIUB somewhere) <!--QuoteEBegin--><!--QuoteEBegin--><Alt><SysRq>-r -- raw (raw keyboard mode, gets keys directly)<!--QuoteEBegin--><!--QuoteEBegin--><Alt><SysRq>-s -- sync (write unsaved files)<!--QuoteEBegin--><!--QuoteEBegin--><Alt><SysRq>-e -- term (gently terminate programs)<!--QuoteEBegin--><!--QuoteEBegin--><Alt><SysRq>-i -- kill (rudely kill programs that didn't finish up with term)<!--QuoteEBegin--><!--QuoteEBegin--><Alt><SysRq>-u -- umount (unmount the file systems, remount read-only) <!--QuoteEBegin--><!--QuoteEBegin--><Alt><SysRq>-b -- reboot<!--QuoteEBegin--><!--QuoteEBegin--> Always follow the sequence in the order given. Ok, how do I check to see if the RAM is ok in Linux?. In WinME, I would simply go to "SYSTEM>DEVICES>RAM" -or- watch the RAM be counted while WinMe was booting up. I'm assuming if it say's "256M RAM" (the amount I currently have) , that everything is working ok(?) Quote Link to comment Share on other sites More sharing options...
qnr Posted April 19, 2003 Report Share Posted April 19, 2003 Well, sometimes it requires test equipment. A common test if you have multiple sticks (for example if your 256M is made up of two 128M sticks) is to try to physically switch the position of the sticks. For example, if it is now slot A - stick 1, slot B - stick 2 -- change it to slot A -- stick 2, slot B -- stick one. Many times, that will clear it up. Again, if you have two sticks, you might try temporarily removing one of them (following all appropriate static guarding procedures) and seeing what happens if you boot with only 128M.... and then do the same with the other stick. Quote Link to comment Share on other sites More sharing options...
Guest ndeb Posted April 19, 2003 Report Share Posted April 19, 2003 Ok, how do I check to see if the RAM is ok in Linux? Use the command cat /proc/meminfo Quote Link to comment Share on other sites More sharing options...
Guest greeneggs Posted April 19, 2003 Report Share Posted April 19, 2003 Ok, how do I check to see if the RAM is ok in Linux? Use the command cat /proc/meminfo Here it is... [teddy@localhost teddy]$ cat /proc/meminfo total: used: free: shared: buffers: cached: Mem: 253931520 195465216 58466304 0 12492800 101953536 Swap: 518152192 0 518152192 MemTotal: 247980 kB MemFree: 57096 kB MemShared: 0 kB Buffers: 12200 kB Cached: 99564 kB SwapCached: 0 kB Active: 48608 kB Inactive: 123952 kB HighTotal: 0 kB HighFree: 0 kB LowTotal: 247980 kB LowFree: 57096 kB SwapTotal: 506008 kB SwapFree: 506008 kB [teddy@localhost teddy]$ Quote Link to comment Share on other sites More sharing options...
Guest ndeb Posted April 19, 2003 Report Share Posted April 19, 2003 Your available memory is 253931520 bytes = 242.16796875 MB. Obviously, ur trident integrated video is stealing atleast 8MB system RAM. Another 6 MB is taken up by the kernel and other stuff. So u have 256MB = 8MB (video) + 6MB (kernel+stuff) + 242MB available So linux is surely detecting all ur system RAM. Quote Link to comment Share on other sites More sharing options...
Ixthusdan Posted April 19, 2003 Report Share Posted April 19, 2003 Two things. 1) Download a 'nix program called memtest86. It will run a continuous program and it will find a problem if one exists. RAM showing up in detect will only error if the first or last chip on the card is the problem. You need a test program to really tell if it is ram. Or lots of ram to switch out. :lol: www.memtest86.com 2) Power supplies under stress are not the only issue. It is also a case of how clean or "regulated" the power is that is being produced. Let's call it poor quality power, which changes and is "dirty". This is actually more common in bad power supplies than simply stressing under use. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.