skrewball

hey i just installed mandrake 9.1 and everything is working fine except for the internet I have run MCC serveral times to try to get it to work but nothing... i even tried deleting the file called eth0:9 here is the output of the following commands.. # ifconfig eth0 Link encap:Ethernet HWaddr 00:0B:DB:B3:78:1E UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:198 errors:0 dropped:0 overruns:0 frame:0 TX packets:15 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:12960 (12.6 Kb) TX bytes:2748 (2.6 Kb) Interrupt:3 Base address:0xe000 Memory:fe9fe000-fe9ff080 eth0:9 Link encap:Ethernet HWaddr 00:0B:DB:B3:78:1E inet addr:169.254.99.115 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:3 Base address:0xe000 Memory:fe9fe000-fe9ff080 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:62 errors:0 dropped:0 overruns:0 frame:0 TX packets:62 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:3914 (3.8 Kb) TX bytes:3914 (3.8 Kb) # ifup eth0 Determining IP information for eth0... done. /sbin/ifup: line 433: 2136 Hangup /etc/init.d/tmdns reload >/dev/null 2>&1 # route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 169.254.0.0 * 255.255.0.0 U 0 0 0 eth0 127.0.0.0 * 255.0.0.0 U 0 0 0 lo # lsmod Module Size Used by Not tainted agpgart 40896 6 (autoclean) i810_audio 26248 0 soundcore 6276 0 [i810_audio] ac97_codec 12488 0 [i810_audio] af_packet 14952 6 (autoclean) sr_mod 16920 0 (autoclean) floppy 55132 0 bcm4400 30432 1 (autoclean) nls_cp850 4316 1 (autoclean) vfat 11820 1 (autoclean) fat 37944 0 (autoclean) [vfat] nls_iso8859-1 3516 2 (autoclean) ntfs 76812 1 (autoclean) supermount 15296 1 (autoclean) ide-cd 33856 0 cdrom 31648 0 [sr_mod ide-cd] ide-scsi 11280 0 scsi_mod 103284 2 [sr_mod ide-scsi] ehci-hcd 18568 0 (unused) usb-uhci 24652 0 (unused) usbcore 72992 1 [ehci-hcd usb-uhci] rtc 8060 0 (autoclean) ext3 59916 1 jbd 38972 1 [ext3] # dmesg | more Broadcom 4401 Ethernet Driver bcm4400 ver. 1.0.1 (08/26/02) eth0: Broadcom BCM4401 100Base-T found at mem fe9fe000, IRQ 3, node addr 000bdbb3781e bcm4400: eth0 NIC Link is Down bcm4400: eth0 NIC Link is Up, 10 Mbps half duplex NETDEV WATCHDOG: eth0: transmit timed out zcip uses obsolete (PF_INET,SOCK_PACKET) device eth0 entered promiscuous mode device eth0 left promiscuous mode #/etc/sysconfig/network-script/ifcfg-eth0 DEVICE=eth0 BOOTPROTO=dhcp NETMASK=255.255.255.0 ONBOOT=yes MII_NOT_SUPPORTED=yes NEEDHOSTNAME=yes hope this helps..

hey i just installed mandrake 9.1 and everything is working fine except for the internet I have run MCC serveral times to try to get it to work but nothing... i even tried deleting the file called eth0:9 here is the output of the following commands.. # ifconfig eth0 Link encap:Ethernet HWaddr 00:0B:DB:B3:78:1E UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:198 errors:0 dropped:0 overruns:0 frame:0 TX packets:15 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:12960 (12.6 Kb) TX bytes:2748 (2.6 Kb) Interrupt:3 Base address:0xe000 Memory:fe9fe000-fe9ff080 eth0:9 Link encap:Ethernet HWaddr 00:0B:DB:B3:78:1E inet addr:169.254.99.115 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:3 Base address:0xe000 Memory:fe9fe000-fe9ff080 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:62 errors:0 dropped:0 overruns:0 frame:0 TX packets:62 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:3914 (3.8 Kb) TX bytes:3914 (3.8 Kb) # ifup eth0 Determining IP information for eth0... done. /sbin/ifup: line 433: 2136 Hangup /etc/init.d/tmdns reload >/dev/null 2>&1 # route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 169.254.0.0 * 255.255.0.0 U 0 0 0 eth0 127.0.0.0 * 255.0.0.0 U 0 0 0 lo # lsmod Module Size Used by Not tainted agpgart 40896 6 (autoclean) i810_audio 26248 0 soundcore 6276 0 [i810_audio] ac97_codec 12488 0 [i810_audio] af_packet 14952 6 (autoclean) sr_mod 16920 0 (autoclean) floppy 55132 0 bcm4400 30432 1 (autoclean) nls_cp850 4316 1 (autoclean) vfat 11820 1 (autoclean) fat 37944 0 (autoclean) [vfat] nls_iso8859-1 3516 2 (autoclean) ntfs 76812 1 (autoclean) supermount 15296 1 (autoclean) ide-cd 33856 0 cdrom 31648 0 [sr_mod ide-cd] ide-scsi 11280 0 scsi_mod 103284 2 [sr_mod ide-scsi] ehci-hcd 18568 0 (unused) usb-uhci 24652 0 (unused) usbcore 72992 1 [ehci-hcd usb-uhci] rtc 8060 0 (autoclean) ext3 59916 1 jbd 38972 1 [ext3] # dmesg | more Broadcom 4401 Ethernet Driver bcm4400 ver. 1.0.1 (08/26/02) eth0: Broadcom BCM4401 100Base-T found at mem fe9fe000, IRQ 3, node addr 000bdbb3781e bcm4400: eth0 NIC Link is Down bcm4400: eth0 NIC Link is Up, 10 Mbps half duplex NETDEV WATCHDOG: eth0: transmit timed out zcip uses obsolete (PF_INET,SOCK_PACKET) device eth0 entered promiscuous mode device eth0 left promiscuous mode #/etc/sysconfig/network-script/ifcfg-eth0 DEVICE=eth0 BOOTPROTO=dhcp NETMASK=255.255.255.0 ONBOOT=yes MII_NOT_SUPPORTED=yes NEEDHOSTNAME=yes hope this helps..

well thanks for all ur help but it still dont work.. maybe 9.2 is just ****ed... if i remember correctly 9.1 connected to the internet but just had resolution issues but i know how to fix that know thaks all

i actually tried to use the network config tool in MCC and i entered all the correct info but still no internet :( any ideas?

i got the driver for the broadcom 440x that came with mdk9.2 installed and appears to be configured correctly but the internet still does not work. I have no idea what to do now.. can any1 help? the results from ifconfig are: eth0 Link encap:Ethernet HWaddr 00:0B:DB:B3:78:1E UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:399 errors:3 dropped:0 overruns:0 frame:3 TX packets:97 errors:0 dropped:0 overruns:0 carrier:1 collisions:1 txqueuelen:100 RX bytes:27834 (27.1 Kb) TX bytes:17926 (17.5 Kb) Interrupt:3 Base address:0xe000 Memory:fe9fe000-fe9ff080 eth0:9 Link encap:Ethernet HWaddr 00:0B:DB:B3:78:1E inet addr:127.255.255.255 Bcast:127.255.255.255 Mask:255.0.0.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:3 Base address:0xe000 Memory:fe9fe000-fe9ff080 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:308 errors:0 dropped:0 overruns:0 frame:0 TX packets:308 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:22422 (21.8 Kb) TX bytes:22422 (21.8 Kb) Thanks :D

?

hmm weird the module is there as b44.o.gz but modprobe b44 :module cannot be found. :o

there was no file named b44.o in //lib/modules/2.4.22-10mdk/kernel/net/drivers/ there wasnt even a drivers directory in the net directory

i actually tried that driver but when i build the binary driver for my kernel i get these errors Executing(%prep): /bin/sh -e /var/tmp/rpm-tmp.5483 + umask 022 + cd /usr/src/RPM/BUILD + cd /usr/src/RPM/BUILD + rm -rf bcm4400-3.0.7 + /bin/mkdir -p bcm4400-3.0.7 + cd bcm4400-3.0.7 + /usr/bin/gzip -dc /usr/src/RPM/SOURCES/bcm4400-3.0.7.tgz + tar -xvvf - -rw-r--r-- root/root 2901 2003-10-28 18:36:56 DISTRIB.TXT -rw-r--r-- root/root 15153 2003-10-28 18:36:56 LICENSE -rw-r--r-- root/root 3100 2003-10-28 18:36:56 Makefile -rw-r--r-- root/root 7988 2003-10-28 18:36:56 README.TXT -rw-r--r-- root/root 7313 2003-10-28 18:36:56 RELEASE.TXT -rw-r--r-- root/root 38701 2003-10-28 18:36:57 b44.h -rw------- root/root 64573 2003-10-28 18:36:57 b44lm.c -rw-r--r-- root/root 17494 2003-10-28 18:36:57 b44lm.h -rw-r--r-- root/root 8474 2003-10-28 18:36:57 b44mm.h -rw-r--r-- root/root 10300 2003-10-28 18:36:57 b44proc.c -rw-r--r-- root/root 11645 2003-10-28 18:36:57 b44queue.h -rw-r--r-- root/root 53199 2003-10-28 18:36:57 b44um.c -rw-r--r-- root/root 6047 2003-10-28 18:36:57 bcm4400.4 + STATUS=0 + '[' 0 -ne 0 ']' + /usr/bin/gzip -dc /usr/src/RPM/SOURCES/bcm4400-3.0.7.tgz + tar -xvvf - -rw-r--r-- root/root 2901 2003-10-28 18:36:56 DISTRIB.TXT -rw-r--r-- root/root 15153 2003-10-28 18:36:56 LICENSE -rw-r--r-- root/root 3100 2003-10-28 18:36:56 Makefile -rw-r--r-- root/root 7988 2003-10-28 18:36:56 README.TXT -rw-r--r-- root/root 7313 2003-10-28 18:36:56 RELEASE.TXT -rw-r--r-- root/root 38701 2003-10-28 18:36:57 b44.h -rw------- root/root 64573 2003-10-28 18:36:57 b44lm.c -rw-r--r-- root/root 17494 2003-10-28 18:36:57 b44lm.h -rw-r--r-- root/root 8474 2003-10-28 18:36:57 b44mm.h -rw-r--r-- root/root 10300 2003-10-28 18:36:57 b44proc.c -rw-r--r-- root/root 11645 2003-10-28 18:36:57 b44queue.h -rw-r--r-- root/root 53199 2003-10-28 18:36:57 b44um.c -rw-r--r-- root/root 6047 2003-10-28 18:36:57 bcm4400.4 + STATUS=0 + '[' 0 -ne 0 ']' + exit 0 Executing(%build): /bin/sh -e /var/tmp/rpm-tmp.5483 + umask 022 + cd /usr/src/RPM/BUILD + cd bcm4400-3.0.7 + make bcm4400.o gcc -DMODULE -D__KERNEL__ -DDBG=0 -Wall -Wstrict-prototypes -O6 -I/lib/modules/2.4.19-24mdk/build/include -c -o b44um.o b44um.c In file included from b44mm.h:28, from b44um.c:57: /usr/include/linux/version.h:2:2: #error "=======================================================" /usr/include/linux/version.h:3:2: #error "You should not include /usr/include/{linux,asm}/ header" /usr/include/linux/version.h:4:2: #error "files directly for the compilation of kernel modules." /usr/include/linux/version.h:5:2: #error "" /usr/include/linux/version.h:6:2: #error "glibc now uses kernel header files from a well-defined" /usr/include/linux/version.h:7:2: #error "working kernel version (as recommended by Linus Torvalds)" /usr/include/linux/version.h:8:2: #error "These files are glibc internal and may not match the" /usr/include/linux/version.h:9:2: #error "currently running kernel. They should only be" /usr/include/linux/version.h:10:2: #error "included via other system header files - user space" /usr/include/linux/version.h:11:2: #error "programs should not directly include <linux/*.h> or" /usr/include/linux/version.h:12:2: #error "<asm/*.h> as well." /usr/include/linux/version.h:13:2: #error "" /usr/include/linux/version.h:14:2: #error "To build kernel modules please do the following:" /usr/include/linux/version.h:15:2: #error "" /usr/include/linux/version.h:16:2: #error " o Have the kernel sources installed" /usr/include/linux/version.h:17:2: #error "" /usr/include/linux/version.h:18:2: #error " o Make sure that the symbolic link" /usr/include/linux/version.h:19:2: #error " /lib/modules/`uname -r`/build exists and points to" /usr/include/linux/version.h:20:2: #error " the matching kernel source directory" /usr/include/linux/version.h:21:2: #error "" /usr/include/linux/version.h:22:2: #error " o Now copy /boot/vmlinuz.version.h to" /usr/include/linux/version.h:23:2: #error " /lib/modules/`uname -r`/build/include/linux/version.h" /usr/include/linux/version.h:24:2: #error "" /usr/include/linux/version.h:25:2: #error " o When compiling, make sure to use the following" /usr/include/linux/version.h:26:2: #error " compiler option to use the correct include files:" /usr/include/linux/version.h:27:2: #error "" /usr/include/linux/version.h:28:2: #error " -I/lib/modules/`uname -r`/build/include" /usr/include/linux/version.h:29:2: #error "" /usr/include/linux/version.h:30:2: #error " instead of" /usr/include/linux/version.h:31:2: #error "" /usr/include/linux/version.h:32:2: #error " -I/usr/include/linux" /usr/include/linux/version.h:33:2: #error "" /usr/include/linux/version.h:34:2: #error " Please adjust the Makefile accordingly." /usr/include/linux/version.h:35:2: #error "=======================================================" In file included from /usr/include/linux/prefetch.h:13, from /usr/include/linux/list.h:6, from /usr/include/linux/module.h:11, from b44mm.h:33, from b44um.c:57: /usr/include/asm/processor.h:55: error: `CONFIG_X86_L1_CACHE_SHIFT' undeclared here (not in a function) /usr/include/asm/processor.h:55: error: requested alignment is not a constant In file included from /usr/include/linux/module.h:297, from b44mm.h:33, from b44um.c:57: /usr/include/linux/version.h:2:2: #error "=======================================================" /usr/include/linux/version.h:3:2: #error "You should not include /usr/include/{linux,asm}/ header" /usr/include/linux/version.h:4:2: #error "files directly for the compilation of kernel modules." /usr/include/linux/version.h:5:2: #error "" /usr/include/linux/version.h:6:2: #error "glibc now uses kernel header files from a well-defined" /usr/include/linux/version.h:7:2: #error "working kernel version (as recommended by Linus Torvalds)" /usr/include/linux/version.h:8:2: #error "These files are glibc internal and may not match the" /usr/include/linux/version.h:9:2: #error "currently running kernel. They should only be" /usr/include/linux/version.h:10:2: #error "included via other system header files - user space" /usr/include/linux/version.h:11:2: #error "programs should not directly include <linux/*.h> or" /usr/include/linux/version.h:12:2: #error "<asm/*.h> as well." /usr/include/linux/version.h:13:2: #error "" /usr/include/linux/version.h:14:2: #error "To build kernel modules please do the following:" /usr/include/linux/version.h:15:2: #error "" /usr/include/linux/version.h:16:2: #error " o Have the kernel sources installed" /usr/include/linux/version.h:17:2: #error "" /usr/include/linux/version.h:18:2: #error " o Make sure that the symbolic link" /usr/include/linux/version.h:19:2: #error " /lib/modules/`uname -r`/build exists and points to" /usr/include/linux/version.h:20:2: #error " the matching kernel source directory" /usr/include/linux/version.h:21:2: #error "" /usr/include/linux/version.h:22:2: #error " o Now copy /boot/vmlinuz.version.h to" /usr/include/linux/version.h:23:2: #error " /lib/modules/`uname -r`/build/include/linux/version.h" /usr/include/linux/version.h:24:2: #error "" /usr/include/linux/version.h:25:2: #error " o When compiling, make sure to use the following" /usr/include/linux/version.h:26:2: #error " compiler option to use the correct include files:" /usr/include/linux/version.h:27:2: #error "" /usr/include/linux/version.h:28:2: #error " -I/lib/modules/`uname -r`/build/include" /usr/include/linux/version.h:29:2: #error "" /usr/include/linux/version.h:30:2: #error " instead of" /usr/include/linux/version.h:31:2: #error "" /usr/include/linux/version.h:32:2: #error " -I/usr/include/linux" /usr/include/linux/version.h:33:2: #error "" /usr/include/linux/version.h:34:2: #error " Please adjust the Makefile accordingly." /usr/include/linux/version.h:35:2: #error "=======================================================" In file included from b44mm.h:33, from b44um.c:57: /usr/include/linux/module.h:299: error: syntax error before "UTS_RELEASE" In file included from /usr/include/linux/mm.h:12, from /usr/include/linux/slab.h:14, from b44mm.h:47, from b44um.c:57: /usr/include/linux/mmzone.h:44: error: `CONFIG_X86_L1_CACHE_SHIFT' undeclared here (not in a function) /usr/include/linux/mmzone.h:44: error: requested alignment is not a constant In file included from /usr/include/asm/hardirq.h:6, from /usr/include/linux/interrupt.h:46, from b44mm.h:48, from b44um.c:57: /usr/include/linux/irq.h:65: error: `CONFIG_X86_L1_CACHE_SHIFT' undeclared here (not in a function) /usr/include/linux/irq.h:65: error: requested alignment is not a constant In file included from /usr/include/linux/interrupt.h:46, from b44mm.h:48, from b44um.c:57: /usr/include/asm/hardirq.h:16: error: `CONFIG_X86_L1_CACHE_SHIFT' undeclared here (not in a function) /usr/include/asm/hardirq.h:16: error: requested alignment is not a constant In file included from b44mm.h:48, from b44um.c:57: /usr/include/linux/interrupt.h:129: error: `CONFIG_X86_L1_CACHE_SHIFT' undeclared here (not in a function) /usr/include/linux/interrupt.h:129: error: requested alignment is not a constant In file included from b44mm.h:51, from b44um.c:57: /usr/include/linux/netdevice.h:165: error: `CONFIG_X86_L1_CACHE_SHIFT' undeclared here (not in a function) /usr/include/linux/netdevice.h:165: error: requested alignment is not a constant In file included from b44mm.h:51, from b44um.c:57: /usr/include/linux/netdevice.h:517: error: `CONFIG_X86_L1_CACHE_SHIFT' undeclared here (not in a function) /usr/include/linux/netdevice.h:517: error: requested alignment is not a constant In file included from b44um.c:57: b44mm.h:123: warning: redefinition of `dma_addr_t' /usr/include/asm/types.h:51: warning: `dma_addr_t' previously declared here In file included from b44um.c:57: b44mm.h:191:1: warning: "DECLARE_PCI_UNMAP_ADDR" redefined In file included from /usr/include/linux/pci.h:654, from b44mm.h:49, from b44um.c:57: /usr/include/asm/pci.h:125:1: warning: this is the location of the previous definition In file included from b44um.c:57: b44mm.h:192:1: warning: "DECLARE_PCI_UNMAP_LEN" redefined In file included from /usr/include/linux/pci.h:654, from b44mm.h:49, from b44um.c:57: /usr/include/asm/pci.h:126:1: warning: this is the location of the previous definition In file included from b44um.c:57: b44mm.h:194:1: warning: "pci_unmap_addr" redefined In file included from /usr/include/linux/pci.h:654, from b44mm.h:49, from b44um.c:57: /usr/include/asm/pci.h:127:1: warning: this is the location of the previous definition In file included from b44um.c:57: b44mm.h:197:1: warning: "pci_unmap_len" redefined In file included from /usr/include/linux/pci.h:654, from b44mm.h:49, from b44um.c:57: /usr/include/asm/pci.h:129:1: warning: this is the location of the previous definition In file included from b44um.c:57: b44mm.h:200:1: warning: "pci_unmap_addr_set" redefined In file included from /usr/include/linux/pci.h:654, from b44mm.h:49, from b44um.c:57: /usr/include/asm/pci.h:128:1: warning: this is the location of the previous definition In file included from b44um.c:57: b44mm.h:203:1: warning: "pci_unmap_len_set" redefined In file included from /usr/include/linux/pci.h:654, from b44mm.h:49, from b44um.c:57: /usr/include/asm/pci.h:130:1: warning: this is the location of the previous definition b44um.c:93:1: warning: "pci_resource_start" redefined In file included from b44mm.h:49, from b44um.c:57: /usr/include/linux/pci.h:751:1: warning: this is the location of the previous definition b44um.c:104: error: conflicting types for `netif_start_queue' /usr/include/linux/netdevice.h:545: error: previous declaration of `netif_start_queue' b44um.c: In function `netif_start_queue': b44um.c:105: error: dereferencing pointer to incomplete type b44um.c:106: error: dereferencing pointer to incomplete type b44um.c:107: error: dereferencing pointer to incomplete type b44um.c: At top level: b44um.c:114: error: conflicting types for `tasklet_schedule' /usr/include/linux/interrupt.h:159: error: previous declaration of `tasklet_schedule' b44um.c:122: error: conflicting types for `tasklet_init' /usr/include/linux/interrupt.h:200: error: previous declaration of `tasklet_init' b44um.c: In function `tasklet_init': b44um.c:123: error: structure has no member named `next' b44um.c: At top level: b44um.c:134: error: redefinition of `struct pci_device_id' b44um.c:141:1: warning: "PCI_ANY_ID" redefined /usr/include/linux/pci.h:354:1: warning: this is the location of the previous definition b44um.c:150:1: warning: "__devexit" redefined In file included from /usr/include/asm/system.h:5, from /usr/include/asm/semaphore.h:39, from /usr/include/linux/fs.h:202, from /usr/include/linux/capability.h:17, from /usr/include/linux/binfmts.h:5, from /usr/include/linux/sched.h:8, from b44mm.h:42, from b44um.c:57: /usr/include/linux/init.h:155:1: warning: this is the location of the previous definition b44um.c:152:1: warning: "SET_MODULE_OWNER" redefined In file included from b44mm.h:33, from b44um.c:57: /usr/include/linux/module.h:411:1: warning: this is the location of the previous definition b44um.c:153:1: warning: "MODULE_DEVICE_TABLE" redefined /usr/include/linux/module.h:336:1: warning: this is the location of the previous definition b44um.c:175: warning: static declaration for `pci_alloc_consistent' follows non-static b44um.c:264: error: `UTS_RELEASE' undeclared here (not in a function) b44um.c: In function `bcm4400_init_board': b44um.c:342: warning: assignment from incompatible pointer type b44um.c:353: error: dereferencing pointer to incomplete type b44um.c:389: error: dereferencing pointer to incomplete type b44um.c:389: error: structure has no member named `base_address' b44um.c:390: error: dereferencing pointer to incomplete type b44um.c:390: error: dereferencing pointer to incomplete type b44um.c:391: error: dereferencing pointer to incomplete type b44um.c:402: warning: passing arg 1 of `unregister_netdev' from incompatible pointer type b44um.c: In function `bcm4400_init_one': b44um.c:449: error: dereferencing pointer to incomplete type b44um.c:450: error: dereferencing pointer to incomplete type b44um.c:451: error: dereferencing pointer to incomplete type b44um.c:452: error: dereferencing pointer to incomplete type b44um.c:453: error: dereferencing pointer to incomplete type b44um.c:454: error: dereferencing pointer to incomplete type b44um.c:455: error: dereferencing pointer to incomplete type b44um.c:461: error: dereferencing pointer to incomplete type b44um.c:462: error: dereferencing pointer to incomplete type b44um.c:465: error: dereferencing pointer to incomplete type b44um.c:468: error: dereferencing pointer to incomplete type b44um.c:468: error: structure has no member named `base_address' b44um.c:469: error: dereferencing pointer to incomplete type b44um.c:480: error: dereferencing pointer to incomplete type b44um.c:480: error: dereferencing pointer to incomplete type b44um.c:483: error: dereferencing pointer to incomplete type b44um.c:483: error: dereferencing pointer to incomplete type b44um.c:484: error: dereferencing pointer to incomplete type b44um.c:487: error: dereferencing pointer to incomplete type b44um.c: In function `bcm4400_remove_one': b44um.c:517: error: dereferencing pointer to incomplete type b44um.c:523: warning: passing arg 1 of `unregister_netdev' from incompatible pointer type b44um.c: In function `bcm4400_open': b44um.c:546: error: dereferencing pointer to incomplete type b44um.c:551: error: dereferencing pointer to incomplete type b44um.c:551: error: dereferencing pointer to incomplete type b44um.c:557: error: dereferencing pointer to incomplete type b44um.c:562: error: dereferencing pointer to incomplete type b44um.c:563: error: dereferencing pointer to incomplete type b44um.c: In function `bcm4400_timer': b44um.c:592: error: dereferencing pointer to incomplete type b44um.c:617: error: dereferencing pointer to incomplete type b44um.c:619: error: dereferencing pointer to incomplete type b44um.c: In function `bcm4400_tx_timeout': b44um.c:651: error: dereferencing pointer to incomplete type b44um.c:654: error: dereferencing pointer to incomplete type b44um.c:657: error: dereferencing pointer to incomplete type b44um.c:658: error: dereferencing pointer to incomplete type b44um.c:662: error: dereferencing pointer to incomplete type b44um.c:662: error: `NET_BH' undeclared (first use in this function) b44um.c:662: error: (Each undeclared identifier is reported only once b44um.c:662: error: for each function it appears in.) b44um.c: In function `bcm4400_start_xmit': b44um.c:668: error: dereferencing pointer to incomplete type b44um.c:681: error: dereferencing pointer to incomplete type b44um.c:689: error: dereferencing pointer to incomplete type b44um.c:692: error: dereferencing pointer to incomplete type b44um.c:692: error: `NET_BH' undeclared (first use in this function) b44um.c:701: error: dereferencing pointer to incomplete type b44um.c:705: error: dereferencing pointer to incomplete type b44um.c:716: error: dereferencing pointer to incomplete type b44um.c:718: error: dereferencing pointer to incomplete type b44um.c: In function `bcm4400_poll': b44um.c:728: error: dereferencing pointer to incomplete type b44um.c:732: error: dereferencing pointer to incomplete type b44um.c:733: error: dereferencing pointer to incomplete type b44um.c:737: error: dereferencing pointer to incomplete type b44um.c:748: warning: passing arg 1 of `netif_rx_complete' from incompatible pointer type b44um.c: In function `bcm4400_interrupt': b44um.c:766: error: dereferencing pointer to incomplete type b44um.c:786: error: dereferencing pointer to incomplete type b44um.c:786: warning: implicit declaration of function `hard_smp_processor_id' b44um.c:828: error: dereferencing pointer to incomplete type b44um.c:828: error: `NET_BH' undeclared (first use in this function) b44um.c: In function `bcm4400_close': b44um.c:855: error: dereferencing pointer to incomplete type b44um.c:859: error: dereferencing pointer to incomplete type b44um.c:861: error: dereferencing pointer to incomplete type b44um.c:876: error: dereferencing pointer to incomplete type b44um.c: In function `bcm4400_freemem': b44um.c:919: error: dereferencing pointer to incomplete type b44um.c: In function `bcm4400_get_stats': b44um.c:939: error: dereferencing pointer to incomplete type b44um.c: In function `netdev_ethtool_ioctl': b44um.c:1029: error: storage size of `ethcmd' isn't known b44um.c:1030: error: dereferencing pointer to incomplete type b44um.c:1034: warning: implicit declaration of function `copy_from_user' b44um.c:1053: error: `ETHTOOL_GSET' undeclared (first use in this function) b44um.c:1055: error: `SUPPORTED_10baseT_Half' undeclared (first use in this function) b44um.c:1056: error: `SUPPORTED_10baseT_Full' undeclared (first use in this function) b44um.c:1057: error: `SUPPORTED_100baseT_Half' undeclared (first use in this function) b44um.c:1058: error: `SUPPORTED_100baseT_Full' undeclared (first use in this function) b44um.c:1059: error: `SUPPORTED_Autoneg' undeclared (first use in this function) b44um.c:1060: error: `SUPPORTED_TP' undeclared (first use in this function) b44um.c:1061: error: `PORT_TP' undeclared (first use in this function) b44um.c:1063: error: `XCVR_INTERNAL' undeclared (first use in this function) b44um.c:1067: error: `SPEED_100' undeclared (first use in this function) b44um.c:1069: error: `SPEED_10' undeclared (first use in this function) b44um.c:1074: error: `DUPLEX_FULL' undeclared (first use in this function) b44um.c:1076: error: `DUPLEX_HALF' undeclared (first use in this function) b44um.c:1079: error: `AUTONEG_ENABLE' undeclared (first use in this function) b44um.c:1080: error: `ADVERTISED_Autoneg' undeclared (first use in this function) b44um.c:1082: error: `ADVERTISED_TP' undeclared (first use in this function) b44um.c:1087: error: `ADVERTISED_10baseT_Half' undeclared (first use in this function) b44um.c:1093: error: `ADVERTISED_10baseT_Full' undeclared (first use in this function) b44um.c:1099: error: `ADVERTISED_100baseT_Half' undeclared (first use in this function) b44um.c:1105: error: `ADVERTISED_100baseT_Full' undeclared (first use in this function) b44um.c:1109: error: `AUTONEG_DISABLE' undeclared (first use in this function) b44um.c:1113: warning: implicit declaration of function `copy_to_user' b44um.c:1117: error: `ETHTOOL_SSET' undeclared (first use in this function) b44um.c:1126: error: `SPEED_1000' undeclared (first use in this function) b44um.c:1029: warning: unused variable `ethcmd' b44um.c: In function `bcm4400_ioctl': b44um.c:1272: error: dereferencing pointer to incomplete type b44um.c: In function `bcm4400_set_rx_mode': b44um.c:1318: error: dereferencing pointer to incomplete type b44um.c:1324: error: dereferencing pointer to incomplete type b44um.c:1324: error: dereferencing pointer to incomplete type b44um.c:1328: error: dereferencing pointer to incomplete type b44um.c:1338: error: dereferencing pointer to incomplete type b44um.c: In function `bcm4400_set_mac_addr': b44um.c:1356: error: dereferencing pointer to incomplete type b44um.c:1358: error: dereferencing pointer to incomplete type b44um.c:1360: error: dereferencing pointer to incomplete type b44um.c:1360: error: dereferencing pointer to incomplete type b44um.c:1360: error: dereferencing pointer to incomplete type b44um.c:1360: error: dereferencing pointer to incomplete type b44um.c:1360: error: dereferencing pointer to incomplete type b44um.c:1361: error: dereferencing pointer to incomplete type b44um.c: In function `cleanup_module': b44um.c:1423: error: dereferencing pointer to incomplete type b44um.c:1428: warning: passing arg 1 of `unregister_netdev' from incompatible pointer type b44um.c: In function `b44_MM_ScheduleRxPoll': b44um.c:1552: warning: passing arg 1 of `netif_rx_schedule_prep' from incompatible pointer type b44um.c:1553: warning: passing arg 1 of `__netif_rx_schedule' from incompatible pointer type b44um.c: In function `b44_MM_AllocateMemory': b44um.c:1653: error: dereferencing pointer to incomplete type b44um.c: In function `b44_MM_MapMemBase': b44um.c:1663: error: structure has no member named `base_address' b44um.c: In function `b44_MM_InitializeUmPackets': b44um.c:1691: warning: assignment from incompatible pointer type b44um.c: In function `b44_MM_IndicateRxPackets': b44um.c:1850: warning: assignment from incompatible pointer type b44um.c: In function `bcm4400_rxfill': b44um.c:1890: warning: assignment from incompatible pointer type b44um.c: In function `b44_MM_IndicateTxPackets': b44um.c:1934: error: dereferencing pointer to incomplete type b44um.c:1934: error: `NET_BH' undeclared (first use in this function) b44um.c:1909: warning: unused variable `i' b44um.c: In function `b44_MM_IndicateStatus': b44um.c:1957: error: dereferencing pointer to incomplete type b44um.c:1961: error: dereferencing pointer to incomplete type b44um.c: In function `b44_MM_FreeRxBuffer': b44um.c:2008: warning: unused variable `pUmDevice' b44um.c: At top level: b44um.c:515: warning: `bcm4400_remove_one' defined but not used make: *** [b44um.o] Error 1 error: Bad exit status from /var/tmp/rpm-tmp.5483 (%build) RPM build errors: Bad exit status from /var/tmp/rpm-tmp.5483 (%build)

here is the following information u requested :D ifup eth0 : bcm4400 device eth0 does not seem to be present, delaying initialization. lsmod : dont see bc440x or anything simalar dmesg : Linux version 2.4.19-24mdk (qateam@updates.mandrakesoft.com) (gcc version 3.2 (Mandrake Linux 9.0 3.2-1mdk)) #1 Thu Jan 30 13:13:07 MST 2003 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 00000000000a0000 (usable) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000000f774000 (usable) BIOS-e820: 000000000f774000 - 000000000f776000 (ACPI NVS) BIOS-e820: 000000000f776000 - 000000000f797000 (ACPI data) BIOS-e820: 000000000f797000 - 000000000f800000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved) BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved) 247MB LOWMEM available. found SMP MP-table at 000fe710 hm, page 000fe000 reserved twice. hm, page 000ff000 reserved twice. hm, page 000f0000 reserved twice. Advanced speculative caching feature not present On node 0 totalpages: 63348 zone(0): 4096 pages. zone(1): 59252 pages. zone(2): 0 pages. Intel MultiProcessor Specification v1.4 Virtual Wire compatibility mode. OEM ID: DELL Product ID: Dim 2400 APIC at: 0xFEE00000 Processor #0 Unknown CPU [15:2] APIC version 20 I/O APIC #1 Version 32 at 0xFEC00000. Processors: 1 Kernel command line: BOOT_IMAGE=2419-24 ro root=304 devfs=mount hdc=ide-scsi acpi=ht resume=/dev/hda5 ide_setup: hdc=ide-scsi Initializing CPU#0 Detected 2192.959 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 4377.80 BogoMIPS Memory: 248136k/253392k available (1176k kernel code, 4872k reserved, 443k data, 132k init, 0k highmem) Dentry cache hash table entries: 32768 (order: 6, 262144 bytes) Inode cache hash table entries: 16384 (order: 5, 131072 bytes) Mount-cache hash table entries: 4096 (order: 3, 32768 bytes) Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes) Page-cache hash table entries: 65536 (order: 6, 262144 bytes) CPU: Before vendor init, caps: bfebfbff 00000000 00000000, vendor = 0 CPU: L1 I cache: 12K, L1 D cache: 8K CPU: After vendor init, caps: bfebfbff 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: After generic, caps: bfebfbff 00000000 00000000 00000000 CPU: Common caps: bfebfbff 00000000 00000000 00000000 CPU: Intel® Celeron® CPU 2.20GHz stepping 09 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 ENABLING IO-APIC IRQs Setting 1 in the phys_id_present_map ...changing IO-APIC physical APIC ID to 1 ... ok. init IO_APIC IRQs IO-APIC (apicid-pin) 1-0, 1-13, 1-20, 1-21, 1-22 not connected. ..TIMER: vector=0x31 pin1=2 pin2=0 number of MP IRQ sources: 29. number of IO-APIC #1 registers: 24. testing the IO APIC....................... IO APIC #1...... .... register #00: 01000000 ....... : physical APIC id: 01 .... register #01: 00178020 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0020 .... register #02: 00000000 ....... : arbitration: 00 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 001 01 0 0 0 0 0 1 1 39 02 001 01 0 0 0 0 0 1 1 31 03 001 01 0 0 0 0 0 1 1 41 04 001 01 0 0 0 0 0 1 1 49 05 001 01 0 0 0 0 0 1 1 51 06 001 01 0 0 0 0 0 1 1 59 07 001 01 0 0 0 0 0 1 1 61 08 001 01 0 0 0 0 0 1 1 69 09 001 01 0 0 0 0 0 1 1 71 0a 001 01 0 0 0 0 0 1 1 79 0b 001 01 0 0 0 0 0 1 1 81 0c 001 01 0 0 0 0 0 1 1 89 0d 000 00 1 0 0 0 0 0 0 00 0e 001 01 0 0 0 0 0 1 1 91 0f 001 01 0 0 0 0 0 1 1 99 10 001 01 1 1 0 1 0 1 1 A1 11 001 01 1 1 0 1 0 1 1 A9 12 001 01 1 1 0 1 0 1 1 B1 13 001 01 1 1 0 1 0 1 1 B9 14 000 00 1 0 0 0 0 0 0 00 15 000 00 1 0 0 0 0 0 0 00 16 000 00 1 0 0 0 0 0 0 00 17 001 01 1 1 0 1 0 1 1 C1 IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ5 -> 0:5 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ10 -> 0:10 IRQ11 -> 0:11 IRQ12 -> 0:12 IRQ14 -> 0:14 IRQ15 -> 0:15 IRQ16 -> 0:16 IRQ17 -> 0:17 IRQ18 -> 0:18 IRQ19 -> 0:19 IRQ23 -> 0:23 .................................... done. Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 2193.0453 MHz. ..... host bus clock speed is 99.6838 MHz. cpu: 0, clocks: 996838, slice: 498419 CPU0<T0:996832,T1:498400,D:13,S:498419,C:996838> mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au) mtrr: detected mtrr type: Intel PCI: PCI BIOS revision 2.10 entry at 0xfbc8f, last bus=1 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) Unknown bridge resource 2: assuming transparent PCI: Using IRQ router PIIX [8086/24c0] at 00:1f.0 PCI->APIC IRQ transform: (B0,I2,P0) -> 16 PCI->APIC IRQ transform: (B0,I29,P0) -> 16 PCI->APIC IRQ transform: (B0,I29,P1) -> 19 PCI->APIC IRQ transform: (B0,I29,P2) -> 18 PCI->APIC IRQ transform: (B0,I29,P3) -> 23 PCI->APIC IRQ transform: (B0,I31,P0) -> 18 PCI->APIC IRQ transform: (B0,I31,P1) -> 17 PCI->APIC IRQ transform: (B0,I31,P1) -> 17 isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16) Starting kswapd VFS: Diskquotas version dquot_6.5.0 initialized devfs: v1.12a (20020514) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A Redundant entry in serial pci_table. Please send the output of lspci -vv, this message (14e4,4212,1028,0001) and the manufacturer and name of serial board or modem board to serial-pci-info@lists.sourceforge.net. register_serial(): autoconfig failed Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH4: IDE controller on PCI bus 00 dev f9 ICH4: chipset revision 1 ICH4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio hda: Maxtor 2F040L0, ATA DISK drive hdc: HL-DT-ST GCE-8481B, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: 80293248 sectors (41110 MB) w/2048KiB Cache, CHS=4998/255/63, UDMA(100) Partition check: /dev/ide/host0/bus0/target0/lun0: p1 p2 p3 < p5 p6 > p4 RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 2048 buckets, 16Kbytes TCP: Hash tables configured (established 16384 bind 32768) Linux IP multicast router 0.06 plus PIM-SM NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. RAMDISK: Compressed image found at block 0 Freeing initrd memory: 96k freed VFS: Mounted root (ext2 filesystem). Mounted devfs on /dev Journalled Block Device driver loaded kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. Mounted devfs on /dev Freeing unused kernel memory: 132k freed Real Time Clock Driver v1.10e usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb-uhci.c: $Revision: 1.275 $ time 13:39:07 Jan 30 2003 usb-uhci.c: High bandwidth mode enabled PCI: Setting latency timer of device 00:1d.0 to 64 usb-uhci.c: USB UHCI at I/O 0xff80, IRQ 16 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected PCI: Setting latency timer of device 00:1d.1 to 64 usb-uhci.c: USB UHCI at I/O 0xff60, IRQ 19 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 2 ports detected PCI: Setting latency timer of device 00:1d.2 to 64 usb-uhci.c: USB UHCI at I/O 0xff40, IRQ 18 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 3 hub.c: USB hub found hub.c: 2 ports detected usb-uhci.c: v1.275:USB Universal Host Controller Interface driver PCI: Setting latency timer of device 00:1d.7 to 64 hcd.c: ehci-hcd @ 00:1d.7, Intel Corp. 82801DB USB EHCI Controller hcd.c: irq 23, pci mem d0072800 usb.c: new USB bus registered, assigned bus number 4 ehci-hcd.c: restricting 64bit DMA mappings to segment 0 ... ehci-hcd.c: USB 2.0 support enabled, EHCI rev 1. 0 hub.c: USB hub found hub.c: 6 ports detected usbdevfs: remount parameter error EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,4), internal journal Adding Swap: 530104k swap-space (priority -1) SCSI subsystem driver Revision: 1.00 scsi0 : SCSI host adapter emulation for IDE ATAPI devices Vendor: HL-DT-ST Model: CD-RW GCE-8481B Rev: C102 Type: CD-ROM ANSI SCSI revision: 02 NTFS driver 2.1.0a [Flags: R/O MODULE]. NTFS-fs warning (device 03:02): parse_options(): Option iocharset is deprecated. Please use option nls=<charsetname> in the future. NTFS volume version 3.1. inserting floppy driver for 2.4.19-24mdk FDC 0 is a post-1991 82077 Attached scsi CD-ROM sr0 at scsi0, channel 0, id 2, lun 0 sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.12 Installing knfsd (copyright © 1996 okir@monad.swb.de). PCI: Setting latency timer of device 00:1f.5 to 64 intel8x0: clocking to 48000 ip_tables: © 2000-2002 Netfilter core team ip_conntrack version 2.1 (1979 buckets, 15832 max) - 304 bytes per conntrack parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE] parport0: irq 7 detected lp0: using parport0 (polling). Linux agpgart interface v0.99 © Jeff Hartmann agpgart: Maximum main memory to use for agp memory: 196M agpgart: Detected an Intel 845G Chipset. agpgart: detected 8060K stolen memory. agpgart: AGP aperture is 128M @ 0xe8000000 memory : cc1f73a0 memory : cc1f73e0 memory : cc1f7420 [drm] AGP 0.99 on Intel i810 @ 0xe8000000 128MB [drm] Initialized i830 1.2.0 20011004 on minor 0 mtrr: base(0xe8020000) is not aligned on a size(0x300000) boundary [drm: i830_unlock] *ERROR* Process 2585 using kernel context 0 memory : cc1f7460

the results from ifconfig are: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:182 errors:0 dropped:0 overruns:0 frame:0 TX packets:182 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:13162 (12.8 Kb) TX bytes:13162 (12.8 Kb)

btw my ethernet card is a Broadcom 440x 10/100 Intergrated Controller

i am running mandrake 9.2 but i am having lots of probs with my ethernet. the mandrake installation picked up my ethernet with no problems but when it came time to configure it to access the interenet whatever i tried didnt seem to work.. i have all the correct information such as DHCP etc. any ideas on what i can do to get the internet to work? Thanks :D

thanks for the help i got the resolution problem worked out :) i got another problem now wich i will create a new thread for

here is my XF86Config-4 file # File generated by XFdrake. Section "Files" # Multiple FontPath entries are allowed (they are concatenated together) # By default, Mandrake 6.0 and later now use a font server independent of # the X server to render fonts. FontPath "unix/:-1" EndSection Section "ServerFlags" AllowMouseOpenFail # allows the server to start up even if the mouse doesn't work #DontZap # disable <Crtl><Alt><BS> (server abort) #DontZoom # disable <Crtl><Alt><KP_+>/<KP_-> (resolution switching) EndSection Section "Module" Load "dbe" # Double-Buffering Extension Load "v4l" # Video for Linux Load "extmod" Load "type1" Load "freetype" Load "glx" # 3D layer Load "dri" # direct rendering EndSection Section "DRI" Mode 0666 EndSection Section "InputDevice" Identifier "Keyboard1" Driver "Keyboard" Option "XkbModel" "pc105" Option "XkbLayout" "en_US" Option "XkbOptions" "" EndSection Section "InputDevice" Identifier "Mouse1" Driver "mouse" Option "Protocol" "IMPS/2" Option "Device" "/dev/psaux" Option "ZAxisMapping" "4 5" EndSection Section "Monitor" Identifier "monitor1" VendorName "Dell" ModelName "Dell E772c" HorizSync 30.0-70.0 VertRefresh 50.0-160.0 # Sony Vaio C1(X,XS,VE,VN)? # 1024x480 @ 85.6 Hz, 48 kHz hsync ModeLine "1024x480" 65.00 1024 1032 1176 1344 480 488 494 563 -hsync -vsync # TV fullscreen mode or DVD fullscreen output. # 768x576 @ 79 Hz, 50 kHz hsync ModeLine "768x576" 50.00 768 832 846 1000 576 590 595 630 # 768x576 @ 100 Hz, 61.6 kHz hsync ModeLine "768x576" 63.07 768 800 960 1024 576 578 590 616 EndSection Section "Device" Identifier "device1" VendorName "Intel Corporation" BoardName "Intel 845" Driver "i810" Option "DPMS" EndSection Section "Screen" Identifier "screen1" Device "device1" Monitor "monitor1" DefaultColorDepth 16 Subsection "Display" Depth 16 Virtual 1024 768 EndSubsection Subsection "Display" Depth 16 Virtual 1024 768 EndSubsection Subsection "Display" Depth 16 Virtual 1024 768 EndSubsection Subsection "Display" Depth 16 Virtual 1024 768 EndSubsection EndSection Section "ServerLayout" Identifier "layout1" InputDevice "Keyboard1" "CoreKeyboard" InputDevice "Mouse1" "CorePointer" Screen "screen1" EndSection