Thanks adamw. Here is my dmesg. I don't know how to read it to see if there is an error message that would apply. Can you look at it to see what gives? Richard....
init init/main.c:718
checking if image is initramfs...it isn't (no cpio magic); looks like a
n initrd
ACPI: Looking for DSDT in initrd ... not found!
Freeing initrd memory: 208k freed
init init/main.c:724
do_basic_setup init/main.c:634
do_basic_setup init/main.c:636
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd160, last bus=4
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: IRQ9 SCI: Level Trigger.
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 7 10) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 7 10) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 7 10) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 7 10) *6
ACPI: PCI Interrupt Link [LNKF] (IRQs 7 10) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs *5)
ACPI: PCI Interrupt Link [LNKH] (IRQs 7 10) *0, disabled.
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: Power Resource [PFN0] (off)
ACPI: Power Resource [PFN1] (off)
Linux Plug and Play Support v0.97 © Adam Belay
PnPBIOS: Disabled
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1f.2[D] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:1f.4[C] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:1f.5 -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:00:1f.6 -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 5
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 10
ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
ACPI: PCI interrupt 0000:02:08.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
ACPI: PCI interrupt 0000:02:0b.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:02:0b.1 -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:02:0c.0 -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:02:0d.0[A] -> GSI 10 (level, low) -> IRQ 10
vesafb: framebuffer at 0xf0000000, mapped to 0xe0807000, size 1875k
vesafb: mode is 800x600x16, linelength=1600, pages=2
vesafb: protected mode interface info at c000:e8c0
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
fb0: VESA VGA frame buffer device
Simple Boot Flag at 0x7c set to 0x1
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1103196849.424:0): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
bootsplash 3.1.6-2004/03/31: looking for picture.... silentjpeg size 14
554 bytes, found (800x600, 14506 bytes, v3).
Console: switching to colour frame buffer device 92x32
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enable
d
PCI: Enabling device 0000:00:1f.6 (0000 -> 0001)
ACPI: PCI interrupt 0000:00:1f.6 -> GSI 10 (level, low) -> IRQ 10
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebu
s=xx
ICH2: IDE controller at PCI slot 0000:00:1f.1
ICH2: chipset revision 5
ICH2: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xcff0-0xcff7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xcff8-0xcfff, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: TOSHIBA MK4018GAP, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: TOSHIBA DVD-ROM SD-R2102, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 78140160 sectors (40007 MB), CHS=65535/16/63, UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 < p5 p6 p7 p8 >
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 1
ACPI: (supports S0 S3 S4 S5)
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
init init/main.c:726
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
ReiserFS: hda5: found reiserfs format "3.6" with standard journal
ReiserFS: hda5: using ordered data mode
ReiserFS: hda5: journal params: device hda5, size 8192, journal first b
lock 18, max trans len 1024, max batch 900, max commit age 30, max tran
s age 30
ReiserFS: hda5: checking transaction log (hda5)
ReiserFS: hda5: Using r5 hash to sort names
Freeing unused kernel memory: 200k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1f.2[D] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1f.2: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: irq 11, io base 0000cf80
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
PCI: Enabling device 0000:00:1f.4 (0000 -> 0001)
ACPI: PCI interrupt 0000:00:1f.4[C] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:1f.4: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1f.4 to 64
uhci_hcd 0000:00:1f.4: irq 10, io base 00001000
uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-1: new full speed USB device using address 2
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 3 ports detected
usb 1-2: new low speed USB device using address 3
usbcore: registered new driver hiddev
input: USB HID v1.00 Mouse [synaptics Inc. Synaptics Touchpad] on usb-0
000:00:1f.2-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
usbcore: registered new driver usbmouse
drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
ts: Compaq touchscreen protocol output
Adding 1068312k swap on /dev/hda2. Priority:-1 extents:1
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 5 (level, low) -> IRQ 5
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-6111 Tue Jul
27 07:55:38 PDT 2004
Linux agpgart interface v0.100 © Dave Jones
agpgart: Detected an Intel i815 Chipset.
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 64M @ 0xf8000000
loop: loaded (max 8 devices)
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
PCI: Enabling device 0000:02:07.0 (0000 -> 0002)
ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:02:07.0 to 64
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Runaway loop while stopping context: ...
ohci1394: fw-host0: Runaway loop while stopping context: ...
ohci1394: fw-host0: Runaway loop while stopping context: ...
ohci1394: fw-host0: Runaway loop while stopping context: ...
ohci1394: fw-host0: OHCI-1394 165.165 (PCI): IRQ=[10] MMIO=[20000000-2
00007ff] Max Packet=[65536]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Serial EEPROM has suspicious values, attempting to
setting max_packet_size to 512 bytes
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/
eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochki
n <saw@saw.sw.com.sg> and others
ACPI: PCI interrupt 0000:02:08.0[A] -> GSI 10 (level, low) -> IRQ 10
eth0: OEM i82557/i82558 10/100 Ethernet, 00:00:39:91:00:E9, IRQ 10.
Board assembly 000000-000, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x04f4518b).
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
bootsplash 3.1.6-2004/03/31: looking for picture.... silentjpeg size 14
554 bytes, found (800x600, 14506 bytes, v3).
bootsplash: status on console 0 changed to on
ACPI: AC Adapter [ADP1] (on-line)
ACPI: Battery Slot [bAT1] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Fan [FAN0] (off)
ACPI: Fan [FAN1] (off)
ACPI: Processor [CPU0] (supports C1 C2)
ACPI: Thermal Zone [THRM] (56 C)
toshiba_acpi: Toshiba Laptop ACPI Extras version 0.18
toshiba_acpi: HCI method: \_SB_.VALD.GHCI
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
PCI: Enabling device 0000:02:0b.0 (0000 -> 0002)
ACPI: PCI interrupt 0000:02:0b.0[A] -> GSI 10 (level, low) -> IRQ 10
Yenta: CardBus bridge found at 0000:02:0b.0 [1179:0001]
Yenta: ISA IRQ mask 0x0018, PCI irq 10
Socket status: 30000007
PCI: Enabling device 0000:02:0b.1 (0000 -> 0002)
ACPI: PCI interrupt 0000:02:0b.1 -> GSI 10 (level, low) -> IRQ 10
Yenta: CardBus bridge found at 0000:02:0b.1 [1179:0001]
Yenta: ISA IRQ mask 0x0018, PCI irq 10
Socket status: 30000011
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x1e0-0x1e7 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
orinoco 0.13e (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roski
n <proski@gnu.org>, et al)
orinoco_cs 0.13e (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Ro
skin <proski@gnu.org>, et al)
eth0: Station identity 001f:0002:0001:0004
eth0: Looks like an Intersil firmware version 1.4.2
eth0: Ad-hoc demo mode supported
eth0: IEEE standard IBSS ad-hoc mode supported
eth0: WEP supported, 104-bit key
eth0: MAC address 00:06:25:16:1E:CF
eth0: Station name "Prism I"
eth0: ready
eth0: index 0x01: Vcc 5.0, irq 3, io 0x0100-0x013f
NET: Registered protocol family 17
eth0: New link status: Connected (0001)
usb 1-1.2: new low speed USB device using address 4
eth0: New link status: Connected (0001)
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1f.2-
1.2
Intel 810 + AC97 Audio, version 1.01, 12:45:05 Oct 1 2004
PCI: Enabling device 0000:00:1f.5 (0000 -> 0001)
ACPI: PCI interrupt 0000:00:1f.5 -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1f.5 to 64
i810: Intel ICH2 found at IO 0x1040 and 0x1400, MEM 0x0000 and 0x0000,
IRQ 10
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
ac97_codec: AC97 Audio codec, id: YMH3 (Unknown)
i810_audio: only 48Khz playback available.
i810_audio: AC'97 codec 0 supports AMAP, total channels = 2
Bluetooth: Core ver 2.6
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.3
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM ver 1.3
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0322b60(lo)
IPv6 over IPv4 tunneling driver
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
bootsplash 3.1.6-2004/03/31: looking for picture.... found (800x600, 10
377 bytes, v3).
bootsplash: status on console 0 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture.... found (800x600, 10 377 bytes, v3).
bootsplash: status on console 1 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture.... found (800x600, 10 377 bytes, v3).
bootsplash: status on console 2 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture.... found (800x600, 10 377 bytes, v3).
bootsplash: status on console 3 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture.... found (800x600, 10 377 bytes, v3).
bootsplash: status on console 4 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture.... found (800x600, 10 377 bytes, v3).
bootsplash: status on console 5 changed to on
eth0: no IPv6 routers present
cdrom: This disc doesn't have any tracks I recognize!
spurious 8259A interrupt: IRQ7.
input: AT Translated Set 2 keyboard on isa0060/serio0
input: AT Translated Set 2 keyboard on isa0060/serio0
[mdk101@toshiba5005 mdk101]$