shams Posted April 20, 2008 Report Share Posted April 20, 2008 hi, i want to use WS-806 CDMA usb modem to connect to the internet but doesn't work i read a tutorial and this is what i did: First i loaded the cdc_acm module and add to the /rc.d/rc.local to load at boot next i did /sbin/lsusb: Bus 002 Device 004: ID 04f2:b016 Chicony Electronics Co., Ltd Bus 002 Device 003: ID 0951:1607 Kingston Technology Bus 002 Device 001: ID 0000:0000 Bus 007 Device 001: ID 0000:0000 Bus 006 Device 001: ID 0000:0000 Bus 005 Device 002: ID 10c4:ea60 Cygnal Integrated Products, Inc. Bus 005 Device 001: ID 0000:0000 Bus 001 Device 001: ID 0000:0000 Bus 004 Device 002: ID 08ff:2580 AuthenTec, Inc. Bus 004 Device 001: ID 0000:0000 Bus 003 Device 001: ID 0000:0000 this is the usb port with which the usb modem is attached: Bus 005 Device 002: ID 10c4:ea60 Cygnal Integrated Products, Inc. then i created a file Cygnal_Integrated.options and put it in the /etc/modprobe.d to laod at boot time, this is the file contents: alias usb:v10C4pEA60* usbserial options usbserial vendor=0x10c4 product=0xea60 after reboot i did: dmesg | grep usb: usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver usb usb1: configuration #1 chosen from 1 choice usb usb2: configuration #1 chosen from 1 choice usb usb3: configuration #1 chosen from 1 choice usb usb4: configuration #1 chosen from 1 choice usb usb5: configuration #1 chosen from 1 choice usb usb6: configuration #1 chosen from 1 choice usb usb7: configuration #1 chosen from 1 choice usb 2-4: new high speed USB device using ehci_hcd and address 3 usb 2-4: configuration #1 chosen from 1 choice usb 2-5: new high speed USB device using ehci_hcd and address 4 usb 2-5: configuration #1 chosen from 1 choice usb 4-1: new full speed USB device using uhci_hcd and address 2 usb 4-1: configuration #1 chosen from 1 choice usb 5-1: new full speed USB device using uhci_hcd and address 2 usb 5-1: configuration #1 chosen from 1 choice usb-storage: device found at 3 usb-storage: waiting for device to settle before scanning usbcore: registered new interface driver usb-storage usb-storage: device scan complete usbcore: registered new interface driver usbserial drivers/usb/serial/usb-serial.c: USB Serial support registered for generic usbserial_generic 5-1:1.0: generic converter detected usb 5-1: generic converter now attached to ttyUSB0 usbcore: registered new interface driver usbserial_generic drivers/usb/serial/usb-serial.c: USB Serial Driver core usbcore: registered new interface driver cdc_acm drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB modems and ISDN adapters But after all that the wvdialconf didn't get connect to the modem and this is the errors: #wvdialconf wvdial.conf Editing `wvdial.conf'. Scanning your serial ports for a modem. Modem Port Scan<*1>: S0 S1 S2 S3 WvModem<*1>: Cannot get information for serial port. ttyUSB0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud ttyUSB0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud ttyUSB0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. Sorry, no modem was detected! Is it in use by another program? Did you configure it properly with setserial? any one can help please? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.