skrewball Posted January 31, 2004 Report Share Posted January 31, 2004 hey i just installed mandrake 9.1 and everything is working fine except for the internet I have run MCC serveral times to try to get it to work but nothing... i even tried deleting the file called eth0:9 here is the output of the following commands.. # ifconfig eth0 Link encap:Ethernet HWaddr 00:0B:DB:B3:78:1E UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:198 errors:0 dropped:0 overruns:0 frame:0 TX packets:15 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:12960 (12.6 Kb) TX bytes:2748 (2.6 Kb) Interrupt:3 Base address:0xe000 Memory:fe9fe000-fe9ff080 eth0:9 Link encap:Ethernet HWaddr 00:0B:DB:B3:78:1E inet addr:169.254.99.115 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:3 Base address:0xe000 Memory:fe9fe000-fe9ff080 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:62 errors:0 dropped:0 overruns:0 frame:0 TX packets:62 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:3914 (3.8 Kb) TX bytes:3914 (3.8 Kb) # ifup eth0 Determining IP information for eth0... done. /sbin/ifup: line 433: 2136 Hangup /etc/init.d/tmdns reload >/dev/null 2>&1 # route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 169.254.0.0 * 255.255.0.0 U 0 0 0 eth0 127.0.0.0 * 255.0.0.0 U 0 0 0 lo # lsmod Module Size Used by Not tainted agpgart 40896 6 (autoclean) i810_audio 26248 0 soundcore 6276 0 [i810_audio] ac97_codec 12488 0 [i810_audio] af_packet 14952 6 (autoclean) sr_mod 16920 0 (autoclean) floppy 55132 0 bcm4400 30432 1 (autoclean) nls_cp850 4316 1 (autoclean) vfat 11820 1 (autoclean) fat 37944 0 (autoclean) [vfat] nls_iso8859-1 3516 2 (autoclean) ntfs 76812 1 (autoclean) supermount 15296 1 (autoclean) ide-cd 33856 0 cdrom 31648 0 [sr_mod ide-cd] ide-scsi 11280 0 scsi_mod 103284 2 [sr_mod ide-scsi] ehci-hcd 18568 0 (unused) usb-uhci 24652 0 (unused) usbcore 72992 1 [ehci-hcd usb-uhci] rtc 8060 0 (autoclean) ext3 59916 1 jbd 38972 1 [ext3] # dmesg | more Broadcom 4401 Ethernet Driver bcm4400 ver. 1.0.1 (08/26/02) eth0: Broadcom BCM4401 100Base-T found at mem fe9fe000, IRQ 3, node addr 000bdbb3781e bcm4400: eth0 NIC Link is Down bcm4400: eth0 NIC Link is Up, 10 Mbps half duplex NETDEV WATCHDOG: eth0: transmit timed out zcip uses obsolete (PF_INET,SOCK_PACKET) device eth0 entered promiscuous mode device eth0 left promiscuous mode #/etc/sysconfig/network-script/ifcfg-eth0 DEVICE=eth0 BOOTPROTO=dhcp NETMASK=255.255.255.0 ONBOOT=yes MII_NOT_SUPPORTED=yes NEEDHOSTNAME=yes hope this helps.. Quote Link to comment Share on other sites More sharing options...
brucer425 Posted February 13, 2004 Report Share Posted February 13, 2004 looks like your not connecting to a dhcp server try setting a ip in for your card and see if that works could be just a bad cable. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.