This file contains a list of laptops on which Mandrake Linux has been successfully installed on. All entries have been contributed by Mandrake users.
Ratings ('Marks') range from 1, worst, to 4, best:
iLuFa - IPC - Lap Power - Maxdata - Mecer - Medion - Micron - Mitac - MTech - NEC - Packard Bell - Panasonic - Patriot - Pico - Portocom - ProStar - Quantex - Rock - Sager - Samsung - Scanport - Sceptre - SEH - Sharp
Model |
Rel. |
Comments / URL |
Mark |
---|---|---|---|
N20U |
8.0 |
Seems all right but the Accton EN2242 ethernet card has
problem when re-installing the device driver. |
3 |
Modell |
Rel. |
Comments / URL |
Mark |
---|---|---|---|
PowerNote500 Green795 |
7.2, 8.0 |
7.2: It was not possible to run XFree 4.x from startup.
Only a warm reboot could start the XServer. 3.3.6 worked fine and with MDK8.0
XFree 4.x too. 8.0: Everything works fine. An USB Mouse works too. |
2, 3 |
same |
8.0 |
none |
3 |
Model |
Rel. |
Comments / URL |
Mark |
---|---|---|---|
Expander |
7.2 |
out of prod. works with 8.0 but slowly |
4 |
Model |
Rel. |
Comments / URL |
Mark |
---|---|---|---|
660T |
8.1 |
X only with framebuffer till XFree 4.2; PCMCIA only
working after manually config; MM-Card and memory stick not supported :-( |
3 |
Model |
Rel. |
Comments / URL |
Mark |
---|---|---|---|
A440+ |
8.0 |
Works very well. |
4 |
Model |
Rel. |
Comments / URL |
Mark |
---|---|---|---|
MD9307 |
8.0 |
It works perfectly, except for the new KDE 2.2.1 (witch
slows down performance- it is also in beta so I think it is normal) |
3 |
MD9399 |
8.0, cooker |
none |
3 |
same |
8.0 |
none |
3 |
Model |
Rel. |
Comments / URL |
Mark |
---|---|---|---|
Transport GX+ |
8.0 |
No problem installing except I had to disable the
mouse pad (PS/2, relieves IRQ12). Maximum screen resolution is 800x600 (with
an ~1" white square roughly centered which won't go away!!!) although my graphics
card (S3 Savage/MX-IX) and screen can handle 1400x1050 (16 Mb of video
RAM). I couldn't manage to fix the screen and PS/2 mouse. |
2 |
same |
8.1 |
I have installed MDK8.1 with very little problems.
But I cannot get the trackpad to work. It works but looks like a 72 image block, no cursor. Just a big white space. Pretty much everything works right out of the box execpt the trackpad and microphone. (pending the testing of the modem) |
3 |
Transport NX |
8.1 |
Installation was mostly successful. Mandrake
fails to recognize PCMCIA card (3com 3CXM056B modem), but otherwise everything
appears fine. |
3 |
Transport Trek |
8.0 |
Installation was flawless. All drivers and hardware were
installed with no problems. |
4 |
Transport ZX |
8.0 |
Version 8.0 does not easily install on this laptop.
The keyboard and/or touchpad is unoperable using the graphical installation interface. |
2 |
same |
7.2, 8.0 |
none |
4,3 |
Transport XPE |
8.0 |
Ran into a couple issues with X. Had to set
console fonts after leaving X and had to add Weight 555 to my XF86Config
file to make it display. Found the answers at http://ofb.net/~jheiss/micronxpe/ Sound and Network (3c589) worked right off the bat with the install. Need to try IR, TV out, etc. when I feel like messing with them. Laptop only has 32Mb of ram and hits swap pretty hard if you do too much at once. I'm running Blackbox wm to minimize the mem shortage. Max is 80Mb so I'll try that and see how much it helps. |
4 |
same |
8.0 |
MIDI sound OPL3 are not set up properly. |
3 |
Model |
Rel. |
Comments /URL |
Mark |
---|---|---|---|
MiNote |
8.0 |
none |
2 |
MiNote 5033 |
7.2, 8.0, 8.1b |
Works very well. Does not start in 8.x (only with kernel
from 7.2). |
4,1,1 |
same |
8.1 |
http://www.spanbroek.net/mark/laptop/
|
4 |
MiNote 6020 |
cooker |
mdk 8 and mdk8.1beta don't work. 8 have a kernel prob.
8.1beta don't know :( |
4(?) |
MiNote 6120N |
8.0, 8.1b |
Needs bios update to ver. 1.07a (for any flavor of Linux).
The rest works well... |
4 |
MiNote 7521 |
8.1b |
SiS 630 display doesn't work well with XFree 3.3.6 and
isn't supported in XFree 4.1. Sound card doesn't work. |
2 |
same |
8.1 |
Had some trouble with the SiS 630 video card, had
to install the XFree86-FBDev server, symlink that server to X and add vga=791
to lilo.conf and it works great. Sound and LAN were recognized
fine. The winmodem doesn't work or the quick start buttons but... |
3 |
Model |
Rel |
Comments / URL |
Mark |
---|---|---|---|
8500 |
8.0 |
needs to be able to turn itself off |
3 |
Model |
Rel. |
Comments / URL |
Mark |
---|---|---|---|
Versa |
8.0 |
Installed well a few adjustments to get x-configured right.
Was my main machine for last 4 months, new to linux and still only O/S on that machine(Dual Boot on new Desktop). Great distro. |
3 |
same |
8.0 |
Everything's fine, I just have to make a small manipulation
to get my mouse back when I'm back from hibernation. Sound is a little low,
I don't know if it's the same under Windows (the machine has never seen it). |
4 |
Versa 6030 |
8.0 |
Perfect, everything (even the built-in modem) is working
properly. |
4 |
Versa 6200MX |
8.0 |
The only thing that seems to make this laptop work properly
(video & sound) is an
XF86Config file that is a modification of 2 that are on the Internet.
It is not clear whether the NEC Versa 6200MX and the NEC 6200MMX are the same computer, but elements of the configuration file for each work excellently with my machine marked Versa 6200MX. |
4 |
Versa 6220 |
8.0 |
none |
3 |
Versa Lite FX |
8.0 |
I works, it worked with the 7.2 as well. |
4 |
same |
8.0 |
It works also with mandrake 7.1 and 7.2. |
4 |
Versa LX |
8.0 |
Installed without a hitch. Sound works fine, and
few video problems(my fault). I'm using a Xircom 10/100 Ethernet adapter and it works flawlessly. |
4 |
same |
8.0 |
none |
4 |
Versa LXi |
8.0 |
The Savage card seems to imply some problems even if XFree
takes it in charge. |
1 |
Versa SX |
8.0f3 |
no problems |
4 |
same |
8.0 |
Works in Mandrake but not in any other distro. |
4 |
Model |
Rel. |
Comments / URL |
Mark |
---|---|---|---|
Easy One 1550 |
8.0, 8.1 |
Mdk 8.0 has sound problems, solved in 8.1. WinModem
problem. |
3 |
Easynote |
8.0 |
Works fine. Only missing support for Lucent WinModem chipset. |
4 |
Easynote VX |
8.0 |
none |
4 |
same |
8.0 |
Unable to turn off tapping on Touchpad (NEC VersaGlide,
possibly ALPS compliant). TV Out not working. ACPI does not report time
left on battery. Otherwise perfect. |
3 |
Model |
Rel. |
Comments / URL |
Mark |
---|---|---|---|
CF-27 |
8.0 |
Sound needs some manual configuration. |
3 |
CF-47 |
7.1,7.2,8.0 |
Occasional PCMCIA NIC errors (happens in Windows as well).
Sound "issues". |
3 |
Model |
Rel. |
Comments / URL |
Mark |
---|---|---|---|
2276 |
8.1 |
Works well, had to change the default video settings to
766 in the bootloader section of the installation. The audio - SiS 7018 is detected, but I cannot get it to work. Also the integrated modem - SmartLink 56K is not detected, no Linmodem available. |
3-4 |
Model |
Rel. |
Comments / URL |
Mark |
---|---|---|---|
982 Consul |
8.0 |
none |
4 |
Consul |
7.0 |
Using linux4Windows. no problems since install 1 year
ago |
4 |
same |
8.0 |
Dual booted with w98, installed OK, but currently have
a problem with the X server. (I know it will work, just haven't had time to
fix it yet). |
1 |
Graduate |
8.0, 8.1 |
A leap of faith is required when installing X as
part of the original install: essentially you get to the point where you
are asked to test the configuration, you say yes and then it all locks up.
Beyond this point, if you do not start with vga=791 as an option, X is a
mess. It took me a few installs and a lot of trawling the email lists to
find that out. However, everything is now groovy... apart from the winmodem! |
3 |
Model |
Rel. |
Comments / URL |
Mark |
---|---|---|---|
924 |
8.0 |
Everything works, except the SMSC IR port and the TV out
of the Neomagic VGA chip. |
3 |
Model |
Rel. |
Comments / URL |
Mark |
---|---|---|---|
1200 |
8.0 |
Install went easy enough, and everything except sound
worked when the machine booted the first time. After a little tinkering
everything is very smooth. I'm really looking forward to running 8.1 when
it is available. |
4 |
2200c |
8.0 |
Once Mandrake stats up the top half and the bottom half
of the screen swap places. |
2 |
same |
8.0 |
To install must use 'linux mem=120M'. also use framebuffer.
winmodem not supported. |
4 |
same |
8.1 |
After a few minutes, the keyboard stops working. |
2 |
3500 |
8.0 |
Had to buy a different modem, but otherwise, everything
seems to be working so far. Works fine with my Zip drive and printer. Took
a few tries to edit the lilo.conf file to give me more time to choose which
OS to boot. Otherwise, so far so good. |
4 |
Model |
Rel. |
Comments / URL |
Mark |
---|---|---|---|
I-1510 |
7.1, 7.2, 8.0 |
Please oh please oh please let me configure my pcnet.o
driven pcmcia card during install...you recognize it and it is up, but you just won't give me the option to configure it. |
2,3,4 |
N30W |
8.0 |
Everything works great except for TV out. Haven't
tried to get winmodem working as I don't use it. |
4 |
Model |
Rel. |
Comments / URL |
Mark |
---|---|---|---|
Pegasus |
8.0 |
Windows Modem, some problems with graphics card after
machine has been on for a while, and then starting X. |
3 |
Sigma 433 |
8.0 |
Build in modem is an LT WinModem. You can download drivers,
but it does crash regularly. |
3 |
Model |
Rel |
Comments / URL |
Mark |
---|---|---|---|
np8550 |
8.0 |
none |
3 |
np8560 |
8.0 |
Won't setup X @ 1400x1050. A manual edit of the horiz
sync from 60 to 85 in XF86Config-4 fixes the problem (along with the appropriate
modelines entries for 1400x1050. voila` 24 bit color at 1400x1050). Copy
of my XF86Config file available upon request
. On board modem will not work. Everything else does! |
4 |
Family Model 8 |
8.0 |
Had to install in unorthodox manner. Did not recognize
LCD. Still having problems with running / keeping it up. |
2 |
Model |
Rel. |
Comments / URL |
Mark |
---|---|---|---|
GT6360 |
8.1b |
Some problems with PCMCIA cards: when I install with Dynalink
FE1500 10/100 Ethernet Card and Melco WLI-PCM-L11 Wireless Network Card
and there is no DHCP server present (at home), the attempt to start X-windows
environment fails with Segmentation Fault. Without cards or in a network
(at work) it works. Other than that, the display refresh rate is frequently
off when switching between text/graphical display modes. |
3 |
VM6000 |
8.0 |
The install freeze with the default kernel. An "unpatch"
of the kernel is needed if you want the 2.4 kernel. |
4 |
same |
7.2 |
Unable to install Mandrake 8.0 on it. |
3 |
Model |
Rel. |
Comments / URL |
Mark |
---|---|---|---|
Gem GN-6150 |
7.2, 8.0 |
No problems with installation, although there does seem
irregularities in recognizing a USB hub and attached printer. Also
some problems for a while in recognizing the floppy drive (only with 8.0)
but this was overcome by installing autofs. |
4 |
Model |
Rel. |
Comments / URL |
Mark |
---|---|---|---|
Soundex 6600T |
8.0 |
Xircom 10/100 model RBE-100 doesn't seem to work |
3 |
same (?) |
8.0 |
8.0 recognised all hardware correctly during install. |
4 |
Soundex 6600 (N30W) |
7.1 - 8.0 |
8.0 found my Kingston KNE-2 LAN card on install
8.1 BETA did not and doesn't have compatible driver. Everything else works
great! |
4 |
Model |
Rel. |
Comments / URL |
Mark |
---|---|---|---|
Designote |
8.0 |
Sound and Graphics work. But DecChip PCMCIA network cards
and Xircom IIps do not work at all |
3 |
Model |
Rel. |
Comments / URL |
Mark |
---|---|---|---|
PC-A280 |
8.1 |
This went beautifully with a network install. The
sound did not work until I ran the hardware configuration utility in drakconf. |
3 |
PC-AX20 |
7.2, 8.0 |
mkd 7.2 works fine, apart from the display being 2cm to
the top, mdk 8.0 is a dead duck, it stops at init2.78 booting. I got round the problem by installing the 2.18 kernel, but the sound does not work, so I went back to 7.2. Hoping 8.1 will be better |
2 |
Acer - Compaq - Dell - IBM - Toshiba
Airis - Cinet - Digital - Hitachi - Sony - Xeron