emilioestevezz Posted October 16, 2003 Report Share Posted October 16, 2003 Hi, i have 2 fisically separated hard drives, in the first one (primary master) i ve got windoze 98 se and on the other (secondary master) i ve got mandrake 9.1 the thing is that when i reboot the pc when it loads the lilo it won´t load nor windows or linux, and began to fill the screen with 99 99 99 99 99 99.... what did i do wrong?? then if i do an fdisk /mbr on the windows hd i can at least boot windows but i cant use the linux hd. any clue??? Thanks. Emilio Quote Link to comment Share on other sites More sharing options...
Peep Posted October 16, 2003 Report Share Posted October 16, 2003 it sounds like LILO isn't loading at all. have you tried reinstalling lilo using the mdk install cd? (boot with the cd, at the prompt: RESCUE and then when the menu comes up, you can restore the bootloader.) it may also be an issue if you recently added a new partition, maybe lilo is looking for operating systems in the wrong partition? (ie, mdk used to be hda5, but after adding a new partition it is hdb1, so you'll need to edit lilo.conf by hand). if you post a bit more info about what modifications you've done lately, i'm sure lots of ppl can chime in with helpful info. Quote Link to comment Share on other sites More sharing options...
Glitz Posted October 16, 2003 Report Share Posted October 16, 2003 Please list your hardrive configuration and your lilo configuration (including which partition you installed it on). I'm guessing that what you want is to have lilo on the windows disk master boot record and tell lilo that windows is on hda1 and linux is on hdb1. I'm guessing here since I don't know the specifics of your partition arrangement. Glitz. Quote Link to comment Share on other sites More sharing options...
shen Posted October 16, 2003 Report Share Posted October 16, 2003 I've seen then quite a few times.. Make sure your HD's are jumpred correctly. One set to Master and the other as Slave. This will have when you have to devices on the same ide channel/cable and the jumpers are set to cable select. This is a popular setting with many prebuilt pc's like dell,hp and such. If both are jumped correctly then it has to be the the boot loader install. Quote Link to comment Share on other sites More sharing options...
SoulSe Posted October 17, 2003 Report Share Posted October 17, 2003 If it makes you feel better, I think we've all had that problem. Check your lilo.conf file carefully, one wrong letter can cause this problem... otherwise, the suggestion of checking your jumpers sounds most likely as your lilo.conf was probably generated, unless you wrote it yourself Quote Link to comment Share on other sites More sharing options...
Guest GorGor Posted October 18, 2003 Report Share Posted October 18, 2003 I am a grub dinosaur and so I am only going on the lilo pdf manual that says some BIOS have trouble if you have configured lilo with COMPACT or not used LBA32. Grub knows about lba32 but I guess you have to be explicit with lilo. I will add some comments to my tips tricks on lilo grub Quote Link to comment Share on other sites More sharing options...
bvc Posted October 18, 2003 Report Share Posted October 18, 2003 Output of info lilo (also in man lilo) BOOT ERRORS The boot process takes place in two stages. The first stage loader is a single sector, and is loaded by the BIOS or by the loader in the MBR. It loads the multi-sector second stage loader, but is very space lim- ited. When the first stage loader gets control, it types the letter "L"; when it is ready to transfer control to the second stage loader it types the letter "I". If any error occurs, like a disk read error, it will put out a hexadecimil error code, and then it will re-try the operation. All hex error codes are BIOS return values, except for the lilo-generated 40, 99 and 9A. A partial list of error codes follows: 00 no error 01 invalid disk command 0A bad sector flag 0B bad track flag 20 controller failure 40 seek failure (BIOS) 40 cylinder>1023 (LILO) 99 invalid second stage index sector (LILO) 9A no second stage loader signature (LILO) AA drive not ready FF sense operation failed Error code 40 is generated by the BIOS, or by LILO during the conver- sion of a linear (24-bit) disk address to a geometric (C:H:S) address. On older systems which do not support lba32 (32-bit) addressing, this error may also be generated. Errors 99 and 9A usually mean the map file (-m or map=) is not readable, likely because LILO was not re-run after some system change, or there is a geometry mis-match between what LILO used (lilo -v3 to display) and what is actually being used by the BIOS (one of the lilo diagnostic disks, available in the source distri- bution, may be needed to diagnose this problem). When the second stage loader has received control from the first stage, it prints the letter "L", and when it has initialized itself, including verifying the "Descriptor Table" - the list of kernels/others to boot - it will print the letter "O", to form the full word "LILO", in upper- case. Boot first CD>F1>rescue>Install linux bootloader. Quote Link to comment Share on other sites More sharing options...
Guest GorGor Posted October 18, 2003 Report Share Posted October 18, 2003 BVC I have just stolen your output and stuck it in my tips section, heh heh. um, the comment I make about /sbin/lilo -v -v -v alludes to the -v3 in your output and is stolen from some post I read , sorry can't remember which one. But I will ramble on, that bios is still an issue for lba or compact. hope that helps the author. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.