Jump to content

Ubuntu 7.10 takes ages to load [solved]


Recommended Posts

Why can't you log in as root? You can do:

 

su

 

to get root privileges and then run dmesg. As for the grub config, this is how it should look:

 

title		Ubuntu 7.10, kernel 2.6.22-14-generic
root		(hd0,0)
kernel		/boot/vmlinuz-2.6.22-14-generic root=UUID=dfe39b72-7dd2-4d0c-af58-5abd9badd4bf ro quiet splash acpi=off
initrd		/boot/initrd.img-2.6.22-14-generic
quiet

title		Ubuntu 7.10, kernel 2.6.22-14-generic (recovery mode)
root		(hd0,0)
kernel		/boot/vmlinuz-2.6.22-14-generic root=UUID=dfe39b72-7dd2-4d0c-af58-5abd9badd4bf ro single acpi=off
initrd		/boot/initrd.img-2.6.22-14-generic

title		Ubuntu 7.10, memtest86+
root		(hd0,0)
kernel		/boot/memtest86+.bin
quiet

 

as mentioned, it goes at the end of the kernel line. You can either edit the file and then reboot, or when booting press ESC to see the grub menu, and then edit on the fly so that it's disabled until you reboot. To edit the file, you need to have root privileges, so unless you can use "su", you have a problem and won't be able to solve it!

Link to comment
Share on other sites

You didn't make this install of the system then? If you did, and don't know what it is, then you can set it up:

 

sudo passwd root

 

you will then be prompted for a password, which is your password - as you are using sudo. Alternatively, if you don't want to change the root password so that you can use su, then you can just do:

 

sudo gedit /boot/grub/menu.lst

 

for example to edit the grub config. Or, as mentioned, boot and edit on the fly from the grub menu.

 

Alternatively, for dmesg:

 

sudo dmesg

Link to comment
Share on other sites

I managed to get acpi=off into menu.lst and also here is the output of dmesg:

 

[	0.000000] Linux version 2.6.22-14-generic (buildd@palmer) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Sun Oct 14 23:05:12 GMT 2007 (Ubuntu 2.6.22-14.46-generic)
[	0.000000] BIOS-provided physical RAM map:
[	0.000000]  BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
[	0.000000]  BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
[	0.000000]  BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
[	0.000000]  BIOS-e820: 0000000000100000 - 000000001be90000 (usable)
[	0.000000]  BIOS-e820: 000000001be90000 - 000000001be9a000 (ACPI data)
[	0.000000]  BIOS-e820: 000000001be9a000 - 000000001bf00000 (ACPI NVS)
[	0.000000]  BIOS-e820: 000000001bf00000 - 0000000020000000 (reserved)
[	0.000000]  BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[	0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[	0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[	0.000000]  BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[	0.000000] 0MB HIGHMEM available.
[	0.000000] 446MB LOWMEM available.
[	0.000000] found SMP MP-table at 000f8110
[	0.000000] Entering add_active_range(0, 0, 114320) 0 entries of 256 used
[	0.000000] Zone PFN ranges:
[	0.000000]   DMA			 0 ->	 4096
[	0.000000]   Normal	   4096 ->   114320
[	0.000000]   HighMem	114320 ->   114320
[	0.000000] early_node_map[1] active PFN ranges
[	0.000000]	 0:		0 ->   114320
[	0.000000] On node 0 totalpages: 114320
[	0.000000]   DMA zone: 32 pages used for memmap
[	0.000000]   DMA zone: 0 pages reserved
[	0.000000]   DMA zone: 4064 pages, LIFO batch:0
[	0.000000]   Normal zone: 861 pages used for memmap
[	0.000000]   Normal zone: 109363 pages, LIFO batch:31
[	0.000000]   HighMem zone: 0 pages used for memmap
[	0.000000] DMI present.
[	0.000000] ACPI: RSDP signature @ 0xC00F8040 checksum 0
[	0.000000] ACPI: RSDP 000F8040, 0014 (r0 ACRSYS)
[	0.000000] ACPI: RSDT 1BE91854, 0038 (r1 ACRSYS   RSDT	6040000  LTP		0)
[	0.000000] ACPI: FACP 1BE99C7F, 0074 (r1 ATI	Bowfin	6040000 ATI	 F4240)
[	0.000000] ACPI: DSDT 1BE9188C, 83F3 (r1   Acer  Navarro  6040000 MSFT  3000000)
[	0.000000] ACPI: FACS 1BE9AFC0, 0040
[	0.000000] ACPI: SLIC 1BE99CF3, 0176 (r1 ACRSYS ACRPRDCT  6040000 LOHR		0)
[	0.000000] ACPI: SSDT 1BE99E69, 0115 (r1 PTLTD  POWERNOW  6040000  LTP		1)
[	0.000000] ACPI: APIC 1BE99F7E, 0046 (r1 PTLTD	   APIC	6040000  LTP		0)
[	0.000000] ACPI: MCFG 1BE99FC4, 003C (r1 PTLTD	MCFG	6040000  LTP		0)
[	0.000000] ATI board detected. Disabling timer routing over 8254.
[	0.000000] ACPI: PM-Timer IO Port: 0x8008
[	0.000000] ACPI: Local APIC address 0xfee00000
[	0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[	0.000000] Processor #0 15:12 APIC version 16
[	0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[	0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[	0.000000] IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23
[	0.000000] ACPI: IRQ9 used by override.
[	0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[	0.000000] Using ACPI (MADT) for SMP configuration information
[	0.000000] Allocating PCI resources starting at 30000000 (gap: 20000000:c0000000)
[	0.000000] Built 1 zonelists.  Total pages: 113427
[	0.000000] Kernel command line: root=UUID=dfe39b72-7dd2-4d0c-af58-5abd9badd4bf ro quiet splash
[	0.000000] mapped APIC to ffffd000 (fee00000)
[	0.000000] mapped IOAPIC to ffffc000 (fec00000)
[	0.000000] Enabling fast FPU save and restore... done.
[	0.000000] Enabling unmasked SIMD FPU exception support... done.
[	0.000000] Initializing CPU#0
[	0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[	0.000000] Detected 1995.197 MHz processor.
[   12.375495] Console: colour VGA+ 80x25
[   12.375691] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[   12.375867] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[   12.383162] Memory: 441476k/457280k available (2015k kernel code, 15204k reserved, 916k data, 364k init, 0k highmem)
[   12.383171] virtual kernel memory layout:
[   12.383172]	 fixmap  : 0xfff4d000 - 0xfffff000   ( 712 kB)
[   12.383174]	 pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[   12.383175]	 vmalloc : 0xdc800000 - 0xff7fe000   ( 559 MB)
[   12.383176]	 lowmem  : 0xc0000000 - 0xdbe90000   ( 446 MB)
[   12.383177]	   .init : 0xc03e3000 - 0xc043e000   ( 364 kB)
[   12.383179]	   .data : 0xc02f7d26 - 0xc03dce84   ( 916 kB)
[   12.383180]	   .text : 0xc0100000 - 0xc02f7d26   (2015 kB)
[   12.383183] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[   12.383214] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[   12.463200] Calibrating delay using timer specific routine.. 3994.24 BogoMIPS (lpj=7988492)
[   12.463221] Security Framework v1.0.0 initialized
[   12.463227] SELinux:  Disabled at boot.
[   12.463238] Mount-cache hash table entries: 512
[   12.463335] CPU: After generic identify, caps: 078bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001d
[   12.463343] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[   12.463345] CPU: L2 Cache: 512K (64 bytes/line)
[   12.463348] CPU: After all inits, caps: 078bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000001d
[   12.463356] Compat vDSO mapped to ffffe000.
[   12.463365] Checking 'hlt' instruction... OK.
[   12.479297] SMP alternatives: switching to UP code
[   12.479437] Freeing SMP alternatives: 11k freed
[   12.479694] Early unpacking initramfs... done
[   12.776157] ACPI: Core revision 20070126
[   12.776249] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[   13.237985] CPU0: AMD Turion(tm) 64 Mobile Technology MK-36 stepping 02
[   13.238003] Total of 1 processors activated (3994.24 BogoMIPS).
[   13.238170] ENABLING IO-APIC IRQs
[   13.238356] ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
[   13.382793] Brought up 1 CPUs
[   13.382887] Booting paravirtualized kernel on bare hardware
[   13.382963] Time: 14:09:28  Date: 01/13/108
[   13.382984] NET: Registered protocol family 16
[   13.383060] EISA bus registered
[   13.383076] ACPI: bus type pci registered
[   13.393962] PCI: BIOS BUG #81[49435000] found
[   13.394002] PCI: Using configuration type 1
[   13.394004] Setting up standard PCI resources
[   13.395494] ACPI: EC: Look up EC in DSDT
[   13.397004] ACPI: EC: GPE=0x10, ports=0x66, 0x62
[   13.415105] ACPI: Interpreter enabled
[   13.415108] ACPI: (supports S0 S3 S4 S5)
[   13.415119] ACPI: Using IOAPIC for interrupt routing
[   13.476584] ACPI: EC: GPE=0x10, ports=0x66, 0x62
[   13.476634] ACPI: PCI Root Bridge [PCI0] (0000:00)
[   13.476642] PCI: Probing PCI hardware (bus 00)
[   13.478629] PCI: Transparent bridge - 0000:00:14.4
[   13.478761] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[   13.478966] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB4_._PRT]
[   13.479115] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB5_._PRT]
[   13.479260] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BB4_._PRT]
[   13.479408] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BB5_._PRT]
[   13.479564] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
[   13.479726] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
[   13.484840] ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled.
[   13.484999] ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled.
[   13.485155] ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled.
[   13.485310] ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled.
[   13.485476] ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled.
[   13.485632] ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled.
[   13.485789] ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled.
[   13.485945] ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled.
[   13.486103] ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 5 7) *0, disabled.
[   13.486209] Linux Plug and Play Support v0.97 (c) Adam Belay
[   13.486226] pnp: PnP ACPI init
[   13.486237] ACPI: bus type pnp registered
[   13.518958] pnp: PnP ACPI: found 10 devices
[   13.518960] ACPI: ACPI bus type pnp unregistered
[   13.518968] PnPBIOS: Disabled by ACPI PNP
[   13.519023] PCI: Using ACPI for IRQ routing
[   13.519026] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[   13.519032] PCI: Cannot allocate resource region 7 of bridge 0000:00:04.0
[   13.519091] PCI: Cannot allocate resource region 8 of bridge 0000:00:04.0
[   13.519143] PCI: Cannot allocate resource region 9 of bridge 0000:00:04.0
[   13.519191] PCI: Cannot allocate resource region 7 of bridge 0000:00:05.0
[   13.519242] PCI: Cannot allocate resource region 8 of bridge 0000:00:05.0
[   13.519420] NET: Registered protocol family 8
[   13.519422] NET: Registered protocol family 20
[   13.519493] pnp: 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
[   13.519501] pnp: 00:01: iomem range 0xfec00000-0xfec00fff could not be reserved
[   13.519504] pnp: 00:01: iomem range 0xfee00000-0xfee00fff could not be reserved
[   13.519510] pnp: 00:08: ioport range 0x1080-0x1080 has been reserved
[   13.519517] pnp: 00:08: ioport range 0x40b-0x40b has been reserved
[   13.519520] pnp: 00:08: ioport range 0x4d0-0x4d1 has been reserved
[   13.519522] pnp: 00:08: ioport range 0x4d6-0x4d6 has been reserved
[   13.519527] pnp: 00:09: iomem range 0xe0000-0xfffff could not be reserved
[   13.519535] pnp: 00:09: iomem range 0xfff00000-0xffffffff could not be reserved
[   13.519537] pnp: 00:09: iomem range 0x0-0xfff could not be reserved
[   13.522679] Time: tsc clocksource has been installed.
[   13.549832] PCI: Bridge: 0000:00:01.0
[   13.549834]   IO window: 9000-9fff
[   13.549841]   MEM window: d0100000-d01fffff
[   13.549844]   PREFETCH window: d4000000-d7ffffff
[   13.549847] PCI: Bridge: 0000:00:04.0
[   13.549848]   IO window: disabled.
[   13.549850]   MEM window: disabled.
[   13.549856]   PREFETCH window: disabled.
[   13.549859] PCI: Bridge: 0000:00:05.0
[   13.549860]   IO window: disabled.
[   13.549862]   MEM window: disabled.
[   13.549864]   PREFETCH window: disabled.
[   13.549878] PCI: Bus 7, cardbus bridge: 0000:06:04.0
[   13.549880]   IO window: 0000a400-0000a4ff
[   13.549885]   IO window: 0000a800-0000a8ff
[   13.549895]   PREFETCH window: 30000000-33ffffff
[   13.549901]   MEM window: 34000000-37ffffff
[   13.549911] PCI: Bridge: 0000:00:14.4
[   13.549914]   IO window: a000-afff
[   13.549921]   MEM window: d0200000-d02fffff
[   13.549930]   PREFETCH window: 30000000-33ffffff
[   13.549952] PCI: Setting latency timer of device 0000:00:04.0 to 64
[   13.549958] PCI: Setting latency timer of device 0000:00:05.0 to 64
[   13.549994] ACPI: PCI Interrupt 0000:06:04.0[A] -> GSI 20 (level, low) -> IRQ 16
[   13.550020] NET: Registered protocol family 2
[   13.586682] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[   13.586721] TCP established hash table entries: 16384 (order: 5, 196608 bytes)
[   13.586872] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[   13.586973] TCP: Hash tables configured (established 16384 bind 16384)
[   13.586975] TCP reno registered
[   13.598744] checking if image is initramfs... it is
[   14.050425] Switched to high resolution mode on CPU 0
[   14.180920] Freeing initrd memory: 7346k freed
[   14.181251] audit: initializing netlink socket (disabled)
[   14.181264] audit(1202911768.080:1): initialized
[   14.182674] VFS: Disk quotas dquot_6.5.1
[   14.182713] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   14.182785] io scheduler noop registered
[   14.182787] io scheduler anticipatory registered
[   14.182789] io scheduler deadline registered
[   14.182801] io scheduler cfq registered (default)
[   14.182809] PCI: MSI quirk detected. MSI deactivated.
[   14.182853] Boot video device is 0000:01:05.0
[   14.182935] PCI: Setting latency timer of device 0000:00:04.0 to 64
[   14.182955] assign_interrupt_mode Found MSI capability
[   14.182958] Allocate Port Service[0000:00:04.0:pcie00]
[   14.183009] PCI: Setting latency timer of device 0000:00:05.0 to 64
[   14.183027] assign_interrupt_mode Found MSI capability
[   14.183029] Allocate Port Service[0000:00:05.0:pcie00]
[   14.183130] isapnp: Scanning for PnP cards...
[   14.537508] isapnp: No Plug & Play device found
[   14.557750] Real Time Clock Driver v1.12ac
[   14.557833] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[   14.558761] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[   14.558904] input: Macintosh mouse button emulation as /class/input/input0
[   14.558965] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSS0] at 0x60,0x64 irq 1,12
[   14.559279] i8042.c: Detected active multiplexing controller, rev 1.1.
[   14.559354] serio: i8042 KBD port at 0x60,0x64 irq 1
[   14.559359] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[   14.559361] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[   14.559364] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[   14.559366] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[   14.559508] mice: PS/2 mouse device common for all mice
[   14.559732] EISA: Probing bus 0 at eisa.0
[   14.559741] Cannot allocate resource for EISA slot 1
[   14.559768] Cannot allocate resource for EISA slot 8
[   14.559769] EISA: Detected 0 cards.
[   14.559913] TCP cubic registered
[   14.559931] NET: Registered protocol family 1
[   14.559949] Using IPI No-Shortcut mode
[   14.560105]   Magic number: 12:52:182
[   14.560162]   hash matches device ttyr8
[   14.560519] Freeing unused kernel memory: 364k freed
[   14.632854] input: AT Translated Set 2 keyboard as /class/input/input1
[   15.731896] AppArmor: AppArmor initialized<5>audit(1202911769.580:2):  type=1505 info="AppArmor initialized" pid=1225
[   15.856667] fuse init (API version 7.8)
[   15.961066] Failure registering capabilities with primary security module.
[   16.064469] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[   16.064481] ACPI Exception (processor_core-0783): AE_NOT_FOUND, Processor Device is not present [20070126]
[   18.560219] ACPI Exception (thermal-0400): AE_NOT_FOUND, Invalid active threshold [0] [20070126]
[   19.659586] ACPI: Thermal Zone [THRM] (35 C)
[   29.207654] usbcore: registered new interface driver usbfs
[   29.207676] usbcore: registered new interface driver hub
[   29.207694] usbcore: registered new device driver usb
[   29.208266] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[   29.208302] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 17
[   29.208315] ohci_hcd 0000:00:13.0: OHCI Host Controller
[   29.208474] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
[   29.208494] ohci_hcd 0000:00:13.0: irq 17, io mem 0xd0004000
[   29.262791] usb usb1: configuration #1 chosen from 1 choice
[   29.262817] hub 1-0:1.0: USB hub found
[   29.262828] hub 1-0:1.0: 4 ports detected
[   29.366725] ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 17
[   29.366740] ohci_hcd 0000:00:13.1: OHCI Host Controller
[   29.366765] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
[   29.366781] ohci_hcd 0000:00:13.1: irq 17, io mem 0xd0005000
[   29.422658] usb usb2: configuration #1 chosen from 1 choice
[   29.422678] hub 2-0:1.0: USB hub found
[   29.422689] hub 2-0:1.0: 4 ports detected
[   29.527054] ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 17
[   29.527069] ehci_hcd 0000:00:13.2: EHCI Host Controller
[   29.527093] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
[   29.527142] ehci_hcd 0000:00:13.2: irq 17, io mem 0xd0006000
[   29.670449] usb 1-4: new low speed USB device using ohci_hcd and address 2
[   29.670474] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   29.670602] usb usb3: configuration #1 chosen from 1 choice
[   29.670625] hub 3-0:1.0: USB hub found
[   29.670631] hub 3-0:1.0: 8 ports detected
[   30.159001] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[   30.159008] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[   30.159628] ATIIXP: IDE controller at PCI slot 0000:00:14.1
[   30.159651] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 18
[   30.159662] ATIIXP: chipset revision 128
[   30.159664] ATIIXP: not 100% native mode: will probe irqs later
[   30.159674]	 ide0: BM-DMA at 0x8410-0x8417, BIOS settings: hda:DMA, hdb:DMA
[   30.159688] ATIIXP: simplex device: DMA disabled
[   30.159689] ide1: ATIIXP Bus-Master DMA disabled (BIOS)
[   30.159694] Probing IDE interface ide0...
[   30.226171] usb 3-4: new high speed USB device using ehci_hcd and address 2
[   30.366020] usb 3-4: configuration #1 chosen from 1 choice
[   30.446495] hda: TOSHIBA MK1234GAX, ATA DISK drive
[   30.590912] 8139too Fast Ethernet driver 0.9.28
[   30.853837] usb 1-4: new low speed USB device using ohci_hcd and address 3
[   31.062846] usb 1-4: configuration #1 chosen from 1 choice
[   31.230085] hdb: Slimtype DVDRW SSM-8515S, ATAPI CD/DVD-ROM drive
[   31.285637] hda: selected mode 0x45
[   31.285728] hdb: selected mode 0x42
[   31.286486] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[   31.427122] usbcore: registered new interface driver hiddev
[   31.432822] input: Logitech USB Optical Mouse as /class/input/input2
[   31.432927] input: USB HID v1.10 Mouse [Logitech USB Optical Mouse] on usb-0000:00:13.0-4
[   31.432939] usbcore: registered new interface driver usbhid
[   31.432943] /build/buildd/linux-source-2.6.22-2.6.22/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[   31.886313] Probing IDE interface ide1...
[   32.450882] SCSI subsystem initialized
[   32.455636] libata version 2.21 loaded.
[   32.457180] ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 21 (level, low) -> IRQ 19
[   32.457967] eth0: RealTek RTL8139 at 0xdc846000, 00:16:d4:5b:25:a1, IRQ 19
[   32.457970] eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
[   32.459560] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[   32.466058] hda: max request size: 512KiB
[   32.472897] hda: 234441648 sectors (120034 MB), CHS=16383/255/63, UDMA(100)
[   32.473043] hda: cache flushes supported
[   32.473088]  hda: hda1 hda2 < hda5 >
[   32.540763] hdb: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
[   32.540772] Uniform CD-ROM driver Revision: 3.20
[   34.405357] Attempting manual resume
[   34.405361] swsusp: Resume From Partition 3:5
[   34.405362] PM: Checking swsusp image.
[   34.503972] PM: Resume from disk failed.
[   35.615446] kjournald starting.  Commit interval 5 seconds
[   35.615456] EXT3-fs: mounted filesystem with ordered data mode.
[  128.939203] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[  128.941746] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[  128.957142] Linux agpgart interface v0.102 (c) Dave Jones
[  130.323036] piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
[  131.299418] ath_hal: module license 'Proprietary' taints kernel.
[  131.300025] ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
[  131.329224] Yenta: CardBus bridge found at 0000:06:04.0 [1025:009f]
[  131.329255] Yenta: Using CSCINT to route CSC interrupts to PCI
[  131.329257] Yenta: Routing CardBus interrupts to PCI
[  131.329263] Yenta TI: socket 0000:06:04.0, mfunc 0x90501212, devctl 0x44
[  131.421761] wlan: 0.8.4.2 (0.9.3.2)
[  131.446313] ath_pci: 0.9.4.5 (0.9.3.2)
[  131.559215] Yenta: ISA IRQ mask 0x0cf8, PCI irq 16
[  131.559220] Socket status: 30000006
[  131.559224] pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
[  131.559227] cs: IO port probe 0xa000-0xafff: clean.
[  131.559402] pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xd02fffff
[  131.559405] pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x33ffffff
[  131.559720] ACPI: PCI Interrupt 0000:06:02.0[A] -> GSI 22 (level, low) -> IRQ 20
[  132.439198] sdhci: Secure Digital Host Controller Interface driver
[  132.439201] sdhci: Copyright(c) Pierre Ossman
[  132.570618] ath_rate_sample: 1.2 (0.9.3.2)
[  132.587406] wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
[  132.587412] wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[  132.587420] wifi0: H/W encryption support: WEP AES AES_CCM TKIP
[  132.587423] wifi0: mac 7.8 phy 4.5 radio 5.6
[  132.587427] wifi0: Use hw queue 1 for WME_AC_BE traffic
[  132.587429] wifi0: Use hw queue 0 for WME_AC_BK traffic
[  132.587431] wifi0: Use hw queue 2 for WME_AC_VI traffic
[  132.587433] wifi0: Use hw queue 3 for WME_AC_VO traffic
[  132.587434] wifi0: Use hw queue 8 for CAB traffic
[  132.587436] wifi0: Use hw queue 9 for beacons
[  132.667837] wifi0: Atheros 5212: mem=0xd0200000, irq=20
[  132.675715] sdhci: SDHCI controller found at 0000:06:04.2 [1524:0550] (rev 1)
[  132.675746] ACPI: PCI Interrupt 0000:06:04.2[B] -> GSI 23 (level, low) -> IRQ 21
[  132.675864] mmc0: SDHCI at 0xd0210800 irq 21 DMA
[  132.680854] sdhci: SDHCI controller found at 0000:06:04.4 [1524:0551] (rev 1)
[  132.680873] PCI: Enabling device 0000:06:04.4 (0000 -> 0002)
[  132.680878] ACPI: PCI Interrupt 0000:06:04.4[B] -> GSI 23 (level, low) -> IRQ 21
[  132.680922] mmc1: SDHCI at 0xd0210100 irq 21 PIO
[  132.683297] ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 18
[  132.783324] input: PC Speaker as /class/input/input3
[  132.985301] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x1280b1, caps: 0xa04713/0x204000
[  133.015831] input: SynPS/2 Synaptics TouchPad as /class/input/input4
[  133.804397] cs: IO port probe 0x100-0x3af: clean.
[  133.806816] cs: IO port probe 0x3e0-0x4ff: clean.
[  133.807764] cs: IO port probe 0x820-0x8ff: clean.
[  133.808567] cs: IO port probe 0xc00-0xcf7: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf
[  133.923405] cs: IO port probe 0xa00-0xaff: clean.
[  135.447548] lp: driver loaded but no devices found
[  135.536367] Adding 1309256k swap on /dev/hda5.  Priority:-1 extents:1 across:1309256k
[  137.486382] EXT3 FS on hda1, internal journal
[  145.013565] No dock devices found.
[  146.227115] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[  146.726854] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[  146.868966] input: Power Button (FF) as /class/input/input5
[  146.872670] ACPI: Power Button (FF) [PWRF]
[  146.903927] input: Lid Switch as /class/input/input6
[  146.907595] ACPI: Lid Switch [LID]
[  146.938851] input: Power Button (CM) as /class/input/input7
[  146.942555] ACPI: Power Button (CM) [PWRB]
[  146.974002] input: Sleep Button (CM) as /class/input/input8
[  146.977690] ACPI: Sleep Button (CM) [SLPB]
[  147.981218] ACPI: Battery Slot [BAT1] (battery present)
[  148.705763] ACPI: AC Adapter [ACAD] (off-line)
[  152.445637] powernow-k8: Found 1 AMD Turion(tm) 64 Mobile Technology MK-36 processors (version 2.00.00)
[  152.445675] powernow-k8:	0 : fid 0xc (2000 MHz), vid 0xe
[  152.445678] powernow-k8:	1 : fid 0xa (1800 MHz), vid 0x10
[  152.445680] powernow-k8:	2 : fid 0x8 (1600 MHz), vid 0x12
[  152.445682] powernow-k8:	3 : fid 0x0 (800 MHz), vid 0x18
[  158.003444] eth0: link down
[  158.641731] ppdev: user-space parallel port driver
[  159.438121] audit(1202911914.195:3):  type=1503 operation="inode_permission" requested_mask="a" denied_mask="a" name="/dev/tty" pid=5021 profile="/usr/sbin/cupsd"
[  159.498793] apm: BIOS not found.
[  163.196823] Failure registering capabilities with primary security module.
[  164.593286] Bluetooth: Core ver 2.11
[  164.593337] NET: Registered protocol family 31
[  164.593340] Bluetooth: HCI device and connection manager initialized
[  164.593343] Bluetooth: HCI socket layer initialized
[  164.615888] Bluetooth: L2CAP ver 2.8
[  164.615892] Bluetooth: L2CAP socket layer initialized
[  164.619402] Bluetooth: RFCOMM socket layer initialized
[  164.619493] Bluetooth: RFCOMM TTY layer initialized
[  164.619496] Bluetooth: RFCOMM ver 1.8
[  162.440000] Marking TSC unstable due to: possible TSC halt in C2.
[  162.444000] Time: acpi_pm clocksource has been installed.
[  163.604000] Clocksource tsc unstable (delta = -163031071 ns)
[  172.864000] hda-intel: Invalid position buffer, using LPIB read method instead.
[  196.816000] NET: Registered protocol family 10
[  196.816000] lo: Disabled Privacy Extensions
[  196.816000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  202.792000] NET: Registered protocol family 17
[  207.784000] ath0: no IPv6 routers present
[  220.000000] ath0: no IPv6 routers present

Link to comment
Share on other sites

Have you rebooted with the acpi=off selected? Did it still take a long time to boot your system?

 

Other parameters you can try to add to the end of the line are:

 

noapic nolapic

 

but do one at a time, and then see if it starts any faster after that. Then report back and let us know.

Link to comment
Share on other sites

Sweet! How do i do that?

See what Ian says here

 

As for the /etc/hosts file, remove its contents and start adding normal addys. A mandatory one should be

127.0.0.1 localhost.localdomain localhost {your-computers-name}

 

EDIT: just realized you use Ubuntu, so probably Ian's post is not the best one for your case. Better look here

Edited by scarecrow
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
 Share

×
×
  • Create New...