Jump to content

Software Manager


Guest ump
 Share

Recommended Posts

Ok

 

here is the deal everytime I try to install somthing via MCC>Software Manager I am told already installed is this suipposed to happen But the prgrams are not installed

 

I have already disabled Supermount thinking that was the problem No Luck

I went to a console and tried to use urpmi but I am told it can't find the command

 

I am running MDK 9

 

Any Ideas

 

ump

Link to comment
Share on other sites

Try rebuilding the rpm database with :

 

#rpm --rebuilddb

 

If you get an error message with the above or it doesn't help, try removing all your sources in mcc>Software Management>Software Sources Manager and readding them afterwards then run the above command again.

Link to comment
Share on other sites

Thanks for the replys I will try when I get back to my Linux box as I am at work and stuck with Microshaft 2000. :cry:

 

cannonfodder all I get is bash:file or command not found (somthing to that effect will check to night and report back exact verbage) :oops:

 

ump

Link to comment
Share on other sites

Guest jglen490
then do rpm --rebuilddb and rpm --initdb

Isn't that backwards? --initdb initializes the rpm database and --rebuilddb rebuilds the database.

Link to comment
Share on other sites

all I get is bash:file or command not found (somthing to that effect will check to night and report back exact verbage)

 

you need to be root to use urpmi (last i looked you had to be). :)

 

Isn't that backwards?  --initdb initializes the rpm database and --rebuilddb rebuilds the database.

 

you might have to do it the way bvc said because you need to rebuild it to working order before initializing for use. just my opinion though.

 

ciao!

Link to comment
Share on other sites

you might have to do it the way bvc said because unless you need to rebuild it to working order before initializing for use. just my opinion though.
Thats been my thinking....besides, if you're having to rebuild the db, it's probably because you're having problems and the db is already initialized. I went through a short period where I was having to do this everytime, so I started doing it before I even tried to install an rpm. After a couple of weeks of this I only have to do it every now an then.
Link to comment
Share on other sites

bvc

 

I did as you suggested then tried to install mplayer via command line got the following

 

urpmi mplayer

To satisfy dependencies, the following packages are going to be installed (6 MB):

libdha0.1-0.90-0.pre7.4mdk.i586

libdv2-0.98-1mdk.i586

libdvdread2-0.9.3-1mdk.i586

libggi-2.0.1-4mdk.i586

libggi2-2.0.1-4mdk.i586

libgii-0.8.1-3mdk.i586

libgii0-0.8.1-3mdk.i586

liblirc0-0.6.5-2mdk.i586

libmad0-0.14.2b-2mdk.i586

mplayer-0.90-0.pre7.4mdk.i586

Is this OK? (Y/n) Y

package libdv2-0.98-1mdk.i586 is not found.

package libdvdread2-0.9.3-1mdk.i586 is not found.

package libmad0-0.14.2b-2mdk.i586 is not found.

package libggi-2.0.1-4mdk.i586 is not found.

package libgii0-0.8.1-3mdk.i586 is not found.

package libgii-0.8.1-3mdk.i586 is not found.

package mplayer-0.90-0.pre7.4mdk.i586 is not found.

package libdha0.1-0.90-0.pre7.4mdk.i586 is not found.

package libggi2-2.0.1-4mdk.i586 is not found.

unable to get source packages, aborting

 

 

So then I went to MCC>Software Manager tried and got the everything already installed message I always get

 

Should I go ahead and remove the sourcves and try adding thenm again as suggested

Link to comment
Share on other sites

Should I go ahead and remove the sourcves and try adding thenm again as suggested
If you don't mind??? I suggest backing them up first. Have you tried to remove _db.0x's>rebuilddb>and then going to mcc>Software Mgr. and updating all your sources>then trying? It's the only other thing I can think to try.
Link to comment
Share on other sites

Well I was finnally able to set up some sources and install one program it's not working but at least my installer is working again

 

thanks for the help

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share

×
×
  • Create New...