mondo

Hello, "You can also use the 2.4 kernel by selecting the LSB (Linux Standard Base?) as one of your packages when your installing MDK. " I installed MDK without selecting LSB, how do I go back to install it (LSB) without installing all over again. Thanks KL

Hi MadKAT, I read some place that the problem might be related to kernel (2.6.3-7mdk) which came with MDK 10.0. Please, please tell me the procedure how-to get apache version 2.0.48. I tried urpmi update but with no luck. I will really appreciate your help here. Thanks KJ

hello, The X window is running. Thanks GH

Hello, I installed MDK 10.0 and I do not see MCC icon on the bottom of my window. What didn't I do? Thanks GH

Hello madKAT, I have also a fresh installed MDK 10, I have apache2 installed, and also webmin. MCC indicates that http is not running. Can you tell me what version of kernel is running on your system ? The httpd2 does not work and the error_log file says " Function not implemented: mod_rewrite: could not create rewrite_log_lock Configuration Failed " Any help will be appreciated. Thanks KJ

Hello Gowator, I have MDK 10.0 and my apache fails to run. Here is the error, When I start apache, the httpd2 failed and I get this in the error_log file "Function not implemented: mod_rewrite: could not create rewrite_log_lock Configuration Failed" Is this a function of kernel which came with mdk 10.0? I would very much appreciate if you you can tell me what mandrake and kernel version are you using for your apache? Thanks MT

hello, "[crit] (38)Function not implemented: mod_rewrite: could not create rewrite_log_lock" I have the above problem with httpd2,and reading the posts here, I became confused. Can somebody tell me howto solve this problem. I am currently running 2.6.3-7mdk. What version of kernel should I use to upgrade the existing one? thanks JH

Hello Steve, "Sorry. Click 'Webmin Configuration', then 'Upgrade Webmin', then make sure "Latest version from www.webmin.com" is selected and click 'Upgrade Webmin". I followed the above process to upgrade the webmin but it failed with the following error; "Failed to upgrade from www.webmin.com: Failed to lookup IP address for www.webmin.com" My internet is working because I can reach www.webmin.com by putting it on address location. What do you think? Thanks MJ

Hello, It takes sometimes (approximately 45 seconds) for user to login to the system, is this a function of the hardware (memory) or is there a parameter in the system that can be changed? Thanks MJ

Hello, When my system boots it automatically starts X. When can I change it so that it starts the terminal and then I can start X manually. Thanks MV

Hello, I installed mandrake 10.0 from CD 1 and it did not asked for both CD 2 and CD 3. What are the packages in these CDs? Thanks MB

Hello somedude, Thanks for your quick reply. "Does anything change when you hit Ctrl Alt and the + or - keys on the numeric pad? " Yes it shrinks and expands with bigger and smaller icons and test. " Your resolution is set to more than what the monitor is set to " How do I solve this problem? Thanks YK

Hello Tyme, " then scroll down to the bottom of your XF86Config-4 file and there will be a section regarding which things to load. " Thanks tyme it worked. Now I can use the mouse to click on the icons. However,three icons; floppy, Hard Disk, Trash and Welcome appear on top of the screen but cannot see the lower bar where web browser, terminal program, and etc are are located at the same time I have to move the cursor up and down on the screen in order to see either the top or bottom icons. I have tried to adjust my screen but no success. Thanks JK

Hello, I installed mandrake 10.0 CE and on reboot 1. The httpd2 failed because could not determine the server's fully qualified domain name, using 127.0.0.1 for serverName. How do I solve this problem ? 2. Could not add loopback device to routing table SIOCADRT: CUPS may not working properly. Thanks MG

Hello somedude, Thanks for your reply. Can you tell me where I can find information howto configure mandrake 10.0. When I installed it, I was prompted with login then login but could not start X windows. With XFdrake configuration tool, I can start X windows but I do not have any information how to use XFdrake. Please let me know where I can get the information. Thanks JB