Slagathor

When I installed, I had to do the no apic kernel at inital boot. because otherwise it would just sit there at finding the HDD controller. I have a Maxtor SATA HDD. But I went ahead and tryed it, and, it shows the same as lm_sensors cept for video card, theres a heading called therm, that sits at 40, never moving. Could the no-apic kernel, I specified on inital boot from DVD be causing the problems????

LM_Sensors doesnt detect the sensors for the CPU or system, just video card. I have a EVGA NF41-SLi motherboard with a EVGA 7800 GT running a AMD 64 +3700 San Diego core CPU, with Mandriva 2006. I desperatly want to start clocking this thing, but, I have to way to monitor temps. (plus I run Folding@Home, and the thjing can get a bit warm, even at default speeds) Any help will be greatly appreciated.......

I wish I could help more, only thing I can think of is something thats need'd isnt installed..... Is your kernel source installed, it needs that, other then that, I am not sure where to go from there.... :unsure:

Heres what I did. Got these drivers http://mxhaard.free.fr/spca50x/Download/sp...20060101.tar.gz extracted them, then opened a console in that folder (theres directions in an install file also) make clean make su to root make install Fired up gqcam and there it was (I may have modeprobe spca5xx, I cant remember right off)

Thanks for the update, I know I tryed these for my Logitec webcam at one time and it didnt work yet. Now it does.......w00t

Speaking of AV, I am using Thunderbird for e-mail, how might I get Klam intagrated with Thunderbird???? Searched there site, and found nothing, also the wiki, I hate wiki's.....

Thank you sir, works a champ.......

ok, made the changes. Will try it when I get home from work....... :D :D

I have Xpee on a small partition on the SATA drive. I also have 2k on the IDE drive. Here my entire lilo.conf When I installed Mandriva, I had the IDE HDD just there for storage, I had XPee on the SATA, then installed Linux on the SATA. It listed the IDE as Windows, even though there was no install on it. Xpee was listed as Windows 1, so I would select that and get to XPee. Now, when I want to get to 2k, which is on the IDE HDD I just select it to boot off that HDD in the BIOS. Perhaps we can work out what the problem is....... # File generated by DrakX/drakboot # WARNING: do not forget to run lilo after modifying this file default="linux" boot=/dev/sda map=/boot/map keytable=/boot/us.klt prompt nowarn timeout=100 message=/boot/message menu-scheme=wb:bw:wb:bw disk=/dev/sda bios=0x80 image=/boot/vmlinuz label="linux" root=/dev/sda6 initrd=/boot/initrd.img append="acpi=ht resume=/dev/sda7 splash=silent" vga=788 read-only image=/boot/vmlinuz label="linux-nonfb" root=/dev/sda6 initrd=/boot/initrd.img append="acpi=ht resume=/dev/sda7" read-only image=/boot/vmlinuz label="failsafe" root=/dev/sda6 initrd=/boot/initrd.img append="failsafe acpi=ht resume=/dev/sda7 devfs=nomount" read-only other=/dev/hda1 label="windows" table=/dev/hda map-drive=0x80 to=0x81 map-drive=0x81 to=0x80 other=/dev/sda1 label="windows1" table=/dev/sda map-drive=0x80 to=0x81 map-drive=0x81 to=0x80

Ok, moved it fine, but uh, when I select XPee, I get a flashing dash and thats it. ANy ideas..... ( I need to get back to it at least one more time)

I can do this in MCC correct?????? Under BOOT, then leave BOOT LOADE TO USE alone, and change boot device from /dev/hda to /dev/sda correct???? IF I do this AFTER I reinstall XPee or 2k, will it still load it up????? Then I can unplug the SATA drive, and put XPee or 2k on the IDE drive. and save all 200 wonderful gigs for Linux......

Well, XPee and Mandrake are on the 200gig SATA drive. I have a crusty old install of XPee on a 10gig partition on the SATA drive. I wanted to reinstall XPee or 2K so to have a fresh install so I can run benchies. ANywase, ya, LILO is on the 20gig HDD, thats just used for storage. Right now bios is set to boot of the 20gig (IDE 1). If I set it to boot from SATA I get a bunch of numbers and crap start to scroll.....heh So, I will give it a try, it's not like I will loose anything, just reinstall some apps if I do manage to fubar it. Just got to remember, dont format my /home partition.......

Ok, here goes, I hope this is in the right spot.......... Ok, I have a 200gig SATA HDD, and a 20gig IDE HDD. When I installed Mandriva, I accidently put LILO on the 20gig IDE HDD. Now, I want to reinstall XPee or 2k on the little partition I had for XPee, on the SATA HDD. Now, the SATA doen not have a MBR, when I set bios to boot from SATA, nada, just some text ont he screen with no ryme or reason.... heh But anywase, to my question, Can I unplug my IDE drive with LILO on, install XPee or 2k on the usual partition, when I need to go to XPee or 2k set the SATA to boot first, then when I need to go back to Linux, set to boot off the IDE. I need a fresh install of XPee or 2K, for benching....... [moved from Software by spinynorman]

But, I have had nothing but issues trying to update nVidia drivers for my 5900XT. nothing worked till I found this at nvnews.net. http://www.nvnews.net/vbulletin/showthread...7608#post637608 Here is whats posted: EDIT: Also, if you want to overclock your video card put. Option "Coolbits" "1" In your XF86Config under Device [moved from Hardware by spinynorman]

I was refering to Steam, I kept getting some goofy error about access violations. Got it working now though......heh Didnt realise there was cedega 4.4.1-1, I was running 4.4.1. I know the petition is written very badly, glad I didnt write it.... (had I written it, it prolly would have been much worse...... )