eikelmt

Hi Artic I have not tested it with other OS(I dont have any) this has been working fine and everything seems to be fine as long as I am connected. I have tried to fine out why I am getting disconnected. here is my ifcfg-eth0: BOOTPROTO=none DEVICE=eth0 MTU="" NETMASK=255.255.255.0 BROADCAST=192.168.0.255 IPADDR=192.168.0.1 WIRELESS_ENC_KEY="" NETWORK=192.168.0.0 MII_NOT_SUPPORTED=yes ONBOOT=yes ifcfg-eth1: GATEWAY=10.0.0.1 BOOTPROTO=none DEVICE=eth1 MTU="" NETMASK=255.0.0.0 BROADCAST=10.255.255.255 IPADDR=10.0.0.1 WIRELESS_ENC_KEY="" NETWORK=10.0.0.0 MII_NOT_SUPPORTED=yes ONBOOT=yes Thank you

yes I have tried to de-select the firewall. eth0 is Netgear and eth1 is 3com 940.. They are working fine. I just have to wait for a while and -- hey I am reconnected. Then while I am writing a post like this I am disconneted again. here is my ifconfig when everything is fine: eth0 Link encap:Ethernet HWaddr 00:0C:6E:E9:BE:21 inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::20c:6eff:fee9:be21/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:147482 errors:0 dropped:0 overruns:0 frame:0 TX packets:146844 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14529556 (13.8 Mb) TX bytes:177596944 (169.3 Mb) Interrupt:11 Memory:fead8000-0 eth1 Link encap:Ethernet HWaddr 00:04:E2:35:20:77 inet addr:10.0.0.1 Bcast:10.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::204:e2ff:fe35:2077/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:319664 errors:4 dropped:0 overruns:0 frame:4 TX packets:0 errors:329718 dropped:0 overruns:0 carrier:659144 collisions:0 txqueuelen:1000 RX bytes:320906607 (306.0 Mb) TX bytes:0 (0.0 B) Interrupt:10 Base address:0xd400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:253094 errors:0 dropped:0 overruns:0 frame:0 TX packets:253094 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:16791378 (16.0 Mb) TX bytes:16791378 (16.0 Mb) ppp0 Link encap:Point-to-Point Protocol inet addr:4.62.200.76 P-t-P:4.62.200.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 RX packets:2427 errors:0 dropped:0 overruns:0 frame:0 TX packets:2715 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:870966 (850.5 Kb) TX bytes:444424 (434.0 Kb)

Hi Guys I need your help. For the moment I am running mdk10 off. My network config is like this: eth0 - internal- 192.168.0.1/24 eth1 - internet- 10.0.0.1 ppp0 - pppoe adsl connection Problem connecting to internet, stay connected and internet connection sharing. Symptom: No internet Cannot connect to localhost.(webmin,ping and xserver is affected). pppoe adapter will still connect. Adsl-status shows:adsl-status: Link is up and running on interface ppp0 ppp0 Link encap:Point-to-Point Protocol inet addr:4.62.200.210 P-t-P:4.62.200.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 RX packets:13590 errors:0 dropped:0 overruns:0 frame:0 TX packets:9654 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:15014327 (14.3 Mb) TX bytes:749377 (731.8 Kb Glxgears gives only 12 FPS and when network is working 780FPS. Error message: ping localhost connect: No buffer space available. This is from my syslog: Aug 14 21:29:50 snoopey kernel: Shorewall:all2all:REJECT:IN= OUT=eth1 SRC=10.0.0.1 DST=10.63.25.28 LEN=28 TOS=0x00 PREC=0x00 TTL=64 ID=12396 DF PROTO=ICMP TYPE=8 CODE=0 ID=5392 SEQ=0 Aug 14 21:29:50 snoopey kernel: Shorewall:all2all:REJECT:IN= OUT=eth1 SRC=10.0.0.1 DST=10.63.25.29 LEN=28 TOS=0x00 PREC=0x00 TTL=64 ID=12397 DF PROTO=ICMP TYPE=8 CODE=0 ID=5392 SEQ=0 Aug 14 21:29:50 snoopey kernel: Shorewall:all2all:REJECT:IN= OUT=eth1 SRC=10.0.0.1 DST=10.63.25.30 LEN=28 TOS=0x00 PREC=0x00 TTL=64 ID=12398 DF PROTO=ICMP TYPE=8 CODE=0 ID=5392 SEQ=0 Aug 14 21:29:50 snoopey kernel: Shorewall:all2all:REJECT:IN= OUT=eth1 SRC=10.0.0.1 DST=10.63.25.31 LEN=28 TOS=0x00 PREC=0x00 TTL=64 ID=12399 DF PROTO=ICMP TYPE=8 CODE=0 ID=5392 SEQ=0 Aug 14 21:29:54 snoopey kernel: printk: 21222 messages suppressed. Aug 14 21:29:54 snoopey kernel: Neighbour table overflow. Aug 14 21:29:59 snoopey kernel: printk: 21676 messages suppressed. Aug 14 21:29:59 snoopey kernel: Neighbour table overflow. Aug 14 21:30:04 snoopey kernel: printk: 21633 messages suppressed. Aug 14 21:30:04 snoopey kernel: Neighbour table overflow. Aug 14 21:30:09 snoopey kernel: printk: 22067 messages suppressed. Aug 14 21:30:09 snoopey kernel: Neighbour table overflow. Well the nexr funny thing is when I leave the pppoe up and running it will re-connect after a while. I am going also to try to use ethereal to capture whats going on with my pppoe. I contacted the isp they asked me of course about my OS and when I said Linux, well have fun in hell.

Hi I have a Sony DC TRV 140 and it is working perfect under MD 10. Sonys instruction is VERY wrong. Go out and buy an i-link cable for 1398 Firewire. The usb cable you have from the box is useless. I talked to Sony and asked them about drivers for open source sinvethey allready is making drivers for MAc, which is very closed to linux. The response was : we are not interested, our products is working fine with windows and that is what we are supporting. Also Sony camera DCS-T1 is working fine with MD. Needs to be set to USB PTP mode. Both Digicam and Gphoto detects it. DC TRV140 works fine with mainactor Best from Tonyjava script:emoticon('')